Thread Number: 44751  /  Tag: Recent Vacuum Cleaners from past 20 years
Power Nozzle Stays On
[Down to Last]

Vacuumland's exclusive eBay Watch:
scroll >>> for more items
Post# 464906   7/29/2023 at 09:48 by MichaelT (Phoenix AZ)        

Hello folks. I just received an Aerus 80th Anniversary Ultralux vacuum. The power nozzle remains on when the vacuum is turned off, and must be manually turned off at the base. I've never run into that before. My other Electrolux and Aerus power nozzles operate with the vacuum. Has anyone else run into this? Not a big deal, but curious and a little annoying. Thanks.

Post# 464907 , Reply# 1   7/29/2023 at 09:56 by kirbylux77 (London, Ontario, Canada)        

kirbylux77's profile picture
If I recall correctly, your model is designed to do that. I think the powerhead was designed to scrub in carpet cleaning powder as well as deep clean carpets.

Post# 464909 , Reply# 2   7/29/2023 at 10:39 by dysonman1 (the county)        

dysonman1's profile picture
I have an 80th myself as well. The power nozzle is not supposed to run after shut-ff. The power nozzle receptacle has two wires and both are connected to the cord leads. Just take the machine apart and correct that one mis-connected wire. The receptacle is wired with the motor so both are energized and de-energized at the same time.

Post# 464911 , Reply# 3   7/29/2023 at 14:01 by human (Pines of Carolina)        

human's profile picture
Sounds like you've got a couple of wires crossed. I did that accidentally on an Electrolux Silverado a few years ago. The power nozzle would come on when the vacuum was off and vice-versa. Seems I plugged two of the wires connecting to the cord winder into the wrong spots when I was putting it back together. It worked normally after I reversed them.

Post# 464915 , Reply# 4   7/29/2023 at 15:44 by Kloveland (Tulsa)        

kloveland's profile picture
I have to agree with Rob on this one. I had an ultralux 80th that was sold thru QVC. It had two PNs. One for regular use and one for carpet cleaning powder. The power nozzle ran it by itself. When the canister was plugged in. You can probably open it up and put the lead from the pn on the switch.



Post# 464916 , Reply# 5   7/29/2023 at 16:09 by Kloveland (Tulsa)        

kloveland's profile picture
Post# 464919 , Reply# 6   7/29/2023 at 17:33 by Lesinutah (Utah)        
If

lesinutah's profile picture
The power wire for the power nozzle isn't connected to the power switch it would stay on. I'd bet money that's exactly what is happening.

Post# 464920 , Reply# 7   7/29/2023 at 18:38 by Kloveland (Tulsa)        

kloveland's profile picture
Also, I dug up my old thread on this.. with the same Ultra Lux I had prior to this one.

CLICK HERE TO GO TO Kloveland's LINK


  View Full Size
Post# 464924 , Reply# 8   7/29/2023 at 22:53 by Lesinutah (Utah)        
If

lesinutah's profile picture
You open up the vacuum connect the power supply of the power nozzle to the switch it will solve the problem.

Post# 464928 , Reply# 9   7/30/2023 at 08:27 by Kloveland (Tulsa)        

kloveland's profile picture
Les, thanks for restating what has been said about five times already.

Post# 464930 , Reply# 10   7/30/2023 at 10:10 by Lesinutah (Utah)        
If

lesinutah's profile picture
If yhe poster listened and said it's fixed I wouldn't. I'm not rambling on giving examples of the problem. I'm simply stating how to fix it.
I don't see the poster posting the problem is fixed.

It's a great observation but I've had this same situation on .......


Post# 464937 , Reply# 11   7/30/2023 at 13:33 by Kloveland (Tulsa)        

kloveland's profile picture
Right but Tom, Edgar and myself. Said the same thing about the pn wire not being connected to the switch. You are simply restating what has already been said.

And was it necessarily a problem if the canister was manufactured that way? Maybe my reading comprehension is bad. But I think the poster was asking if anyone else has encountered the same problem.


Post# 464939 , Reply# 12   7/30/2023 at 14:41 by Lesinutah (Utah)        
Its

lesinutah's profile picture
A forum where you ask questions. The posters in here don't always connect the dots. If I posted s video and evidence and show empathy for the poster would that help?
I told them how to fix it. You can view it how u want but not everyone on here is mechanically inclined. You view the post as him needing empathy and I view it as someone needing to know how to fix a problem .
Agree to disagree it's a power nozzle.


Post# 464943 , Reply# 13   7/30/2023 at 15:11 by Kloveland (Tulsa)        

kloveland's profile picture
Ok

Post# 464955 , Reply# 14   7/30/2023 at 23:33 by maytag142c (Somewhere over the rainbow. )        
Dri Lux

maytag142c's profile picture
I actually have a NOS Dri Lux with 2 unopened containers of capture. I believe the owners manual is with it too. Itís boxed up and ready to ship if anyone has any interest in it.

Post# 464956 , Reply# 15   7/30/2023 at 23:59 by MichaelT (Phoenix AZ)        
Power Nozzle Stays On

Hello everyone. Thank you all for the posts and information. I appreciate your input and always learn something when I ask a question.

I'm not good with tools and repairs, unfortunately. I rely on a really great vac guy here in Phoenix to repair and keep my vintage machines running well.

I find the power nozzle issue isn't too annoying; I did wonder if an electrical issue was the culprit, and it appears to be the case. I guess I'll live with it unless I have any additional problems.

Thank you all very much for your assistance.

Michael


Post# 464963 , Reply# 16   7/31/2023 at 07:44 by kloveland (Tulsa)        

kloveland's profile picture

Michael is yours the same blue UltraLux 80th plastic canister that I have pictured in my above posts and in my video? I want to make sure that we are talking about the same vacuum.

I apologize if it seems like I'm throwing an autistic fit over this post. I want to drive home the point that if it is the same UltraLux as pictured. It came from the factory that way.  It's not an electrical issue. Below is a post from Danrob1 back in 2012 when I asked the same question. 

 

 



CLICK HERE TO GO TO kloveland's LINK

  View Full Size
Post# 465331 , Reply# 17   8/16/2023 at 11:54 by MichaelT (Phoenix AZ)        
Power Nozzle Stays On

Hi Kloveland. My Ultralux is identical to the one you pictured. It's labeled 80th Anniversary and has the electronic panel with the indicator lights (these don't work, however; I suspect the electronic part died. It happened on my Guardian Ultra, too). I've seen a picture of the Dri Clean nozzle and didn't realize what it was for. I got my Ultralux from ebay and it only has the suction nozzle. It works fine from the switch on the nozzle.

Post# 465333 , Reply# 18   8/16/2023 at 14:14 by kirbylux77 (London, Ontario, Canada)        

kirbylux77's profile picture
Michael, if I was you, I would leave the vacuum alone and NOT rewire it so the powerhead shuts off when you shut off the vacuum. Remember - Aerus intentionally manufactured the Ultralux this way, for a specific purpose, so that the DriLux powerhead could be used with it for dry carpet cleaning with Capture carpet cleaning powder. If you rewire the vacuum so the powerhead shuts off with the canister on/off switch, you're removing a "feature". And with it, part of what makes it "unique", and possibly a sought-after model in the future that makes it more valuable & collectible. If you ever decide to sell it, you may regret it if removing that "feature" made your cleaner less desirable to a collector, and less valuable. And you can live with it by simply shutting off the powerhead separately, not a big deal.

I would look into getting the lights fixed though. It's not electronic, it's all solid state stuff inside. The Aerus Lux Legacy is still made with the lighted control panel, chances are it's a easy fix.


Post# 465336 , Reply# 19   8/16/2023 at 15:37 by MichaelT (Phoenix AZ)        
Power Nozzle Stays On

Hi Kirbylux77. Thank you for the advice. I agree with you and I'm not going to mess with the vacuum electrical wiring. I don't really mind turning the nozzle off at the base and I may run into a Dri Lux nozzle again at some point. I did see one on ebay a while back, but didn't know what I was looking at. I had the circuit board on my Guardian Ultra replaced (it stopped working, but the temperature light glowed) and it was $235 from my Aerus dealer. I decided to hold off on fixing the Ultralux due to the cost.

Post# 465337 , Reply# 20   8/16/2023 at 15:40 by MichaelT (Phoenix AZ)        
Dri Lux Nozzle

Hi Maytag142c. How much are you asking for the Dri Lux nozzle with the Capture cleaner? I hadn't heard of this until I read the replies to my question on this forum, and I'm interested in it. My email is mlt562003@yahoo.com.

Thanks.

Michael T.


Post# 465338 , Reply# 21   8/16/2023 at 17:29 by Maytag142C (Somewhere over the rainbow. )        

maytag142c's profile picture
Hey Michael!

I actually sold it to another collector about 2 weeks ago while he was here visiting. It now resides in Missouri.

Cassidy


Post# 465341 , Reply# 22   8/16/2023 at 18:24 by MichaelT (Phoenix AZ)        
Dri Lux Nozzle

Hi Maytag142C. No problem. Thanks for the reply.

Michael


Post# 465348 , Reply# 23   8/17/2023 at 03:08 by Maytag142C (Somewhere over the rainbow. )        

maytag142c's profile picture
Of course! ☺️

Post# 465351 , Reply# 24   8/17/2023 at 09:12 by dysonman1 (the county)        
Kenny

dysonman1's profile picture
Do you think your UltraLux was wired the way it was, because it was sold on QVC to include the Dri Lux? My UltraLux came from the Aerus store and had only the one power nozzle and was wired 'standard'.

Post# 465359 , Reply# 25   8/17/2023 at 16:18 by kloveland (Tulsa)        

kloveland's profile picture
Yes, I'm fairly certain it was to run the Dri-clean power nozzle without the suction from the canister. This is my second one of the exact same model and both would run with the canister switch off.

I'm going off of what Danorob1 said in his post. I put a link to the original post in the archives below.


CLICK HERE TO GO TO kloveland's LINK


  View Full Size

Forum Index:       Other Forums:                      



Comes to the Rescue!

Woops, Time to Check the Bag!!!
Either you need to change your vacuum bag or you forgot to LOG-IN?

Discuss-O-MAT Log-In



New Members
Click Here To Sign Up.



                     


automaticwasher.org home
Discuss-o-Mat Forums
Vintage Brochures, Service and Owners Manuals
Fun Vintage Washer Ephemera
See It Wash!
Video Downloads
Audio Downloads
Picture of the Day
Patent of the Day
Photos of our Collections
The Old Aberdeen Farm
Vintage Service Manuals
Vintage washer/dryer/dishwasher to sell?
Technical/service questions?
Looking for Parts?
Website related questions?
Digital Millennium Copyright Act Policy
Our Privacy Policy