Thread Number: 40591  /  Tag: 50s/60s/70s Vacuum Cleaners
Electrolux model F
[Down to Last]

Vacuumland's exclusive eBay Watch:
scroll >>> for more items --- [As an eBay Partner, eBay may compensate vacuumland.org if you make a purchase using any link to eBay on this page]
Post# 431265   9/4/2020 at 22:49 (1,301 days old) by DetroitDirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Hello, new here. I’m trying to restore my mothers Electrolux model F vacuum. I need a few parts, thought I might get lucky here. I need the original braided hose, 1 Front rubber bumper, switch , cord reel. I can’t seem to find a parts vac. Any help would be awesome. I’ll see if I can attach pics.
I just bought 2 alum tubes, but they have the wrong finish on.
I have the owners manual, and all the attachments.


  View Full Size
Post# 431302 , Reply# 1   9/5/2020 at 11:51 (1,300 days old) by Jo (Dallas,TX)        
You’ve hit a good place

That’s a great Electrolux. I have the same model among others.

Are you attempting to use this with a power nozzle? It doesn’t look like yours has the port for it, it would be a little outlet with a rubber door on the side of the top trim, from the pic you included it’s hard to tell if it has it because the dusting brush may be obscuring it from view. It’s usually on the left side of that top trim as viewed in this picture.

For a hose best bet is to get a rubber or plastic one. Available on eBay or hescos.inc. Has some generics at a very reasonble price for a plastic or rubber non electric one. Just make sure the end that attaches to the main unit is identical as there are many different ones. If you need a power hose you’ll need a pigtail electric hose but they are hard to come by and there tend to be more used braided ones available. The braided ones were prone to failure by disintegrating from the interior out so while it may look good, it could be bad and there’s no way to tell until it’s in your possession and do the hose test. The way you test is by first running the vac with no hose and covers the suction port with your hand and feel that there should be virtually no air coming out of the blower end when you do this and also note the tone of the motor at this time. Next attach a hose and cover the suction end of the hose handle with one hand and feel if there is air coming out of the blower port, and also compare if the time of the vacuum sounds as strained as it did without the hose, if there is a air, and a lot of it coming out of the blower port and the tone of the motor isn’t as strained, the hose is leaking and sucking air through it’s length. The rubber and plastic hoses don’t have this issue.

If you are interested in going direct to the dealer you will need to locate your local Aerus dealer. Website is aerusvacuums.com. The name changed from Electrolux to Aerus in 2003 so the company still exists. They may be able to help you with some parts you want and also check out rvavacuums.com and Rayks son has a lot of experience in restor8ng the old models so you may want to contact him as well to get the bumper and switch if Aerus tells you they are discontinued. Some aftermarket companies make generic parts for these vacuums and that may be the only option for the switch.

The wands were made in both aluminum and steel over the era and my AF (as the model is typically called) had the steel ones which are heavier duty but also heavier. Any wands will do nicely that are Electrolux and it appears you have a set of mid 80s aluminum ones and they should be fine...the mid 80s aluminum had a more frosty type finish to them.

Not sure if you need a cord halo..one is not shown on the vac in the picture, they are inexpensive and screw on around the blower port. There is a screw hole on either side.. It is for standing the vacuum on its end to change the bag and also to wrap the cord on for storage. There was also an optional cord winder for this model..model 2 has the direct plug in cord on it and it screws on in place of the cord halo.

eBay is a great resource for used parts and model AE, and model G used the same switch. Model L, R, E, AE, use the same cord halo.

Bumper may be hard to find, I had one long ago that had them, but my current one wasn’t equipped with them.

eBay is your best bet for parts. Look up vintage Electrolux followed by the part you want. The more general you are the more you might find what you want because not all sellers list by model letter or proper name of the part as they may not know it.

Let us know if you have more questions. I’ve done a lot of work on many models including the AF so should be able to help you get what you need.

Jon


Post# 431339 , Reply# 2   9/5/2020 at 20:29 (1,300 days old) by DetroitDirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Hey thanks. Yes, I have the cord winter, but the recoil is broke. I also have all the attachments, manual and receipt. It was just over 100 in 1959. I can post either if you want to see.

Post# 431359 , Reply# 3   9/6/2020 at 09:24 (1,299 days old) by DetroitDirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Here’s a few pics. The hose does leak where it spins. There’s a gap in there.

  Photos...       <              >      Photo 1 of 4         View Full Size
Post# 431364 , Reply# 4   9/6/2020 at 11:06 (1,299 days old) by DetroitDirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I just figured out the switch, just the gray plastic rocker I need, I put a new cord on a t the vac works nice.
If someone has a rubber bumper and the gray rocker switch, it’s all I need.
The rubber part in the flip brush has a separation, another one would be nice, but this one works. One in the tan would be nice, this one was replaced to teal at some point.


Post# 431382 , Reply# 5   9/6/2020 at 16:31 (1,299 days old) by DetroitDirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
What is the gray dial for on the front?

Post# 431409 , Reply# 6   9/7/2020 at 08:43 (1,298 days old) by DetroitDirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I found this bag, from the 70’s, I remember my mom buying it to save on buying bags. A reusable Dirt Bag, It almost ruined the vac, her Electrolux fancy rep/ repairman yelled at her, lol. Dirt was going rite through into the motor.

  View Full Size
Post# 431497 , Reply# 7   9/8/2020 at 19:20 (1,297 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I just bought 2 flip brushes on eBay, I won’t need all the parts, any one needs any I’ll have some Extras, some in teal and tan.

Post# 431518 , Reply# 8   9/9/2020 at 09:23 (1,296 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture


  Photos...       <              >      Photo 1 of 2         View Full Size
Post# 431564 , Reply# 9   9/9/2020 at 20:39 (1,296 days old) by Jo (Dallas,TX)        
Automatic control dial

The dial in the front regulates the sensitivity of the automatic control feature which pops the bag door open and shuts the cleaner off to signal you to check for a full bag. The machine constantly monitors the suction provided by the cleaner on both sides of the bag, before and after it, as the bag fills with dirt suction will be reduced as the dirt clogs the pores and the bag door will pop open when there is a significant imbalance of suction before and after the bag caused by the bag filling with dirt. A lower number setting makes the system very sensitive to a small loss of suction from a minimal amount of dirt in the bag and a higher number allows it to tolerate a higher loss of suction before popping open.

Fine dust such as powder, ash, and plaster dust will clog a bag’s pores very quickly causing a loss of suction even with the bag not full...and conversely, a bag full of pet hair doesn’t cut off much suction at all and could be stuffed before popping open. So if you need to vacuum fine dust you’ll need a higher number to complete the job without the machine continuing to pop open and for a job with coarse dirt such as pet hair you’ll want a lower number to make sure it signals when it’s full so you aren’t over packing the bag.

For an average home dirt usually 3 is a good number but I usually set my machine on 1 or 2 when I put a new bag in and when it pops open, if it’s not full enough to change I select the next higher number and close it and continue vacuuming until it pops open and is full enough to change the bag or I feel the cleaner has lost enough suction that warrants I put a new bag in to restore suction to peak. I like to use a lower setting for carpet so I insure I have the best suction always for carpet that it is not compromised by the bag filled. For hard floors the machine works well even at reduced suction so I will tolerate a higher setting which will allow for less suction efficiency as the bag fills so I can put more dirt in the bag.

Basically the dial adjusts how quickly the automatic “Check bag” feature occurs. Lower number advances its operation to most frequent and a higher number “retards” it’s operation so you can continue cleaning even though suction is getting blocked off by the dirt accumulation in the bag and fit more dirt in the bag.

It is recommended not to stuff the bag, but rather change it when 2/3 full to allow for good air flow to keep the motor cool and not run the machine at a strain due to blocked suction from a filled bag. The highest number 6 is really just if you are vacuuming fine powder and need to get the job done without it stopping, and then you should change the bag and reset the dial to a “regular” lower number when done.

Your manual should have a page explaining this but it doesn’t really tell you exactly how it works, just how to set it. It doesn’t tell you if it’s adjusting suction or not. It’s actually monitoring the cleaners suction at all times when it is on. Some people think it adjusts suction but it does not, it just allows the machine to operate at a higher amount of suction loss (Inefficiency) due to the bag filling with dirt on each higher numbered setting.

The nice thing is that this system is a constant performance monitor to constantly monitor the machines cleaning efficiency and signal when it is diminishing by the bag filling with dirt which depletes suction.

The first machine this system was introduced on was the model LX and it did not have an adjustment dial and people were going through too many bags too quickly, the addition of the dial allows the user to tweak the automatic control to their specific needs or composition of dirt in their home and also make an exception for a special job such as fine powdery dirt so one would not have to use a bunch of bags to get that type of dirt job completed.

A hint: if you do need to clean fine dust, setting your machine on 5 or 6 is ok for the job and if it pops open you can take the bag out and flick the sides or shake the bag down and reinsert, this will restore better suction as it will clear the bags sides of the powdery dirt and allow it to pile at the bottom of the bag and allow more of this dirt to be added to the bag.

I have one I use as a shop vac and on these types of jobs I usually do that to help restore the bags suction so I can get the task completed without having to change the bag. Sometimes I’ll do this 2 or 3 times before I change the bag but if it’s popping open on 6, it’s time to just change it for sure as running the machine in this state could wear out your motor prematurely.

The cordwinder can be rewound or if the spring coil has broken a new one is available from Aerus. The biggest thing you must pay attention to is that the spring be wound on a few times around so that when the cord is fully extended it doesn’t get pulled off the spool but not so little that it hampers the rewind strength. It takes experience to roll up a cord reel spring and assemble the whole thing and once it’s wound it has to be installed onto the base carefully and held to not unwind while doing so. The cordwinders contacts and raceway tracks should be cleaned and adjusted for good contact.

The switch yes has a rocker cover and a mechanism under it. Rumor is the mechanism is discontinued but I’m not certain of that for sure. The mechanism is pretty sturdy and can be cleaned if spark residue has built up.

You may want to search ebay for a model F for parts...it’s possible you may get some that way.

Looks like you have a plastic hose which should give you good suction performance.

The original rug and floor tool with the model AF has the cleaner switch on the side end which makes turns on the gleaner bar on the rug side of the tool which helps to pick up hair and lint better it could stick on loop type carpet or loop upholstery so on those surfaces it should be switched off which exposes a smooth side. The carpet side of the tool generally shouldn’t be used on hard surfaces but if it is the gleaner should be switched off as it could be damaged on the hard surface or damage the hard surface itself. I keep mine off unless it’s needed then switch it back off once I’m done with the task needing it. The rubber bumpers sometimes come available on eBay but sounds like you got an entirely new one.

Jon


Post# 431581 , Reply# 10   9/10/2020 at 09:14 (1,295 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Hey thanks a lot for all the info, I will look into getting the reel fixed, Yes, I picked up 2 flip brushes, one with a perfect tan rubber bumper on it, one with real, It has a teal insert now, I’m almost sure that and the teal rubber part didn’t come on it and was replaced, if I it was tan, what color should the melal part in the center brush side be? Tan or teal?
The rubber hose is prob from the 80’s. I remember when it went. We had duct tape on the old one for years.
One of the front rubber bumpers on the front is missing. I’ll keep an eye out for those, the other side is tore as well, so I’d like to find 2
Plexi cleaner and a tooth brush took of years of dirt off all the plastic parts, that’s all I use on plastic, I found that out cleaning up car interior plastic.
My mom loved this vac and would have been delighted on the work I’ve done to it. Now the Vac just gets a retired life, I have race deck floor in the garage, now it just does that and it’s a conversation pc with the car guys.
I’ll post up pics of the flip brushes when they come. I will have some extra parts from the 2, leme know if any here needs parts.


Post# 431589 , Reply# 11   9/10/2020 at 13:17 (1,295 days old) by Jo (Dallas,TX)        
Color schemes

The light cream wirh teal is a model G, model R and white model L color scheme. The metal part for the bristles would have been turquoise like a model G body.

The all cream or tan colored flip tools are from the 1974-1982 golden jubilee, superJ and Olympia eras with the metal bristle holder either in light blue metallic, gold metallic or brown metallic respectively.

The elbows for the Golden jubilee and super J were metal and the Olympia version in 1980 began a change to plastic. To tune up your rug and floor tools spritz the elbow swivel part with just a quick squirt of WD-40. And spin it around and wipe off any excess with a paper towel. You’ll be amazed at how nicely the tool will work by this little trick. An Electrolux service man showed me this back in the mid 80s as well as some other places to lubricate such as the hose swivel handle and inside the track where the hose attaches to the bag door. Just a wipe of WD-40 or silicone spray is all you need to make things move like new. Lubricate the swivel wheel underneath and the back wheels too. The ball bearings and the ball bearing tracks too on the inside of the cord winder.

The correct coloring for a model AF flip over rug and floor tool would match the machine in the beigey gray with the bumper being in cream and the metal bristle holder would be beigey gray too. I have one for mine and can take a picture and post for you. Also the design of the rug side was different from the updated style that has the single suction slot, the first style had a double slot.

The model R cleaner was also the identical colors to the AF but the attachments I believe we’re the cream and teal because it was the lower line model during the model G era which was after the AF.

Those bumpers for the bag door are rare as they are exclusive to the AF and not all AF’s had them at all. They are nice to have but I think will be a challenge to get and you might want to contact Ray’s son at rvavacuums.com to see if he has any. Those will prove to be your biggest challenge.

The cloth dust bags are ok if there’s no holes but fine dust could go through....for household dirt they are ok. Though they clog quickly and cause suction loss much more quickly than the 4 ply palate bags feom the late 80s to early 2000s which really work nicely. Plus when the automatic control engages and pops the door open with a cloth bag some dirt often dumps on the floor because the whole system is cyclonic and the dirt actually accumulated up near the bag door first but the center where the dirt comes in stays clear. The bag fills over time accumulating the dirt up near the top of the bag and then down the sides usually leaving the bottom clear. This occurs this way on paper or cloth bags.

My Dad uses older Electrolux’s In the basements of both of his homes because he does a lot of woodworking and has a lot of sawdust to clean up so we have cloth bags in the basement machines so we can just dump them into a trash can. To properly clear a cloth bag you should put it gasket side down on a piece of paper or the ground d and hold it at the gasket then shake it and wait for the dust to settle then carefully lift the bag off. Or if you have another vacuum you can suck the dust off the bag cloth. Periodically hold it up to the light to check for any holes.

To clean your motor you can take off the top and switch and unscrew the top and bottom screws to remove the back end of the cleaner, the. Using a compressor and the air blower attachment, blow the dust out of the motor getting in all the nooks and crannies. Do this outside. You’ll be amazed at how when you are done the motor will look like new. I just did it to mine a few months ago for the first time ever and was amazed. Removing built up dust helps the motor to run cooler and last longer. Clean the gasket between the back of the cleaner and also blow out the back of the cleaner air baffle writh the compressed air too. There’s is a felt part in there that will no doubt be dusty.

The rubber hose actually looks like it is not all that old, it is generic and looks very similar to the ones sold today so it might be more recent.

Growing up my best friends mom had and likely still has an AF. She never changes anything. Hers is a little later version like mine with the model G Turquoise colored braided hose. Her tools matched the cleaner base colors. I believe her crevice tool was teal. Mine didn’t come to me with a crevice tool and I’m not sure what color the originals would have been, likely teal...I haven’t seen any from that era in creamy tan, those were started in 1974 with the Golden Jubilee and continued until 1982. The old teal ones were a harder plastic and sometimes cracked unlike the cream Tan colored one In your picture so perhaps your Mom got a new one at some point.

Forgive any typos. Using my iphone and the autocorrect often messes things up. Hopefully you understand if the wrong word or typo got inserted.

Jon


Post# 431595 , Reply# 12   9/10/2020 at 15:03 (1,295 days old) by Jo (Dallas,TX)        
Genuine AF rug and floor tool

Here’s pics of my AF rug and floor tool in correct matching coloring. The darker main part has yellowed a little over the years, but this is the correct matching coloring and as you can tell it matches the dusting brush upholstery tool coloring combination.

Note the difference in the rug side design, the air opening in the center is wider and the channels going to either side are narrow with that blocked out section in the middle on either side. I’ve never tested which design does a better job but I imagine the newer design made an improvement for more even suction along the whole width of the tool.

Jon


  Photos...       <              >      Photo 1 of 6         View Full Size
Post# 431614 , Reply# 13   9/10/2020 at 20:12 (1,295 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
The owners manual says model F, what’s AF?

Post# 431616 , Reply# 14   9/10/2020 at 20:35 (1,295 days old) by Jo (Dallas,TX)        
Look on the bottom

The bottom of the bag door underneath it says model Automatic F. Electrolux showed it as either F or AF. F would be the original intention. Previous to the model Automatic F there was an Automatic E and an E. The E did not have the automatic control and was the lower level model of the E series. So after the AE it seemed normal to call the Automatic F the AF for short and that’s how it got to be sort of nicknamed the AF. I think the Electrolux chart shows it as the “AF“. During the F series, the model S for “Special” model was the lower level model of the two but was colored in a light bluish gray with a white bag door and white back end and no cord reel or cord wrap halo.

Jon


Post# 431638 , Reply# 15   9/11/2020 at 14:34 (1,294 days old) by Jo (Dallas,TX)        
Colors not always consistent

Also, the colors of the tools and attachments supplied with every machine were also not always consistent. It really depended on what the factory was producing at the time. Usually the attachments were colored to go along with the current top of the line model and paired with the lower level model even if the color was different. Since the top of the line models and lower level models did not always share the same color scheme and years in production often the models that were sold at the end of an era had mismatched attachments. For example, my Mother’s Blue Model L from 1972 had all color correct everything. However a neighbor who I ended up cleaning for had a Blue Model L she bought in November 1975 and it had a gold Golden Jubilee era colored hose and also a Golden Jubilee chrome power nozzle with white bumper and those were the colors it came with as a brand new unit. The combo dusting upholstery tool and crevice tool, flip rug and floor tool, and external hose wrap wiring and power nozzle sheath were all the blue color. I’ve seen other inconsistencies on machines that were sold new with different colored hoses or attachments here and there so it is possible the rug and floor tool with teal bumper and turquoise metal bristle holder was the one supplied with your Mom’s vac when new as Electrolux may have changed the coloring for the new model G soon to come out and had depleted the model F colored ones and so hers got the new color combination one....Looking at your picture of the receipt it looks like your Mom purchased the F on December 19, 1959? I put a question mark because I’m not sure that’s a 59 or 57 for the year. But based on the production run of the F from 1957-1960 and the G coming out in 1960 it’s likely your Mom’s may have just come equipped with the tan and teal rug and floor tool if they had transitioned the coloring of those to the G colors already by the time her machine was being produced and already discontinued the F colors for the rug and floor tool and depleted the F colored Supply. You can probably make it out better than me from the picture. Usually the bumpers don’t wear out that quickly nor the entire tool to warrant replacement and it would have had to have been replaced by 1967 which was the end of the teal and tan attachments so I’m willing to bet the rug and floor tool is the original that was supplied with the machine even though it was colored incorrectly. During the run of the F the design of the carpet side of the rug and floor tool was also changed to the newer single suction channel about a half inch wide all the way across design. They may have changed the colors at that time as well if they knew the G colors were going to be changing.

There are some People on here, including the creator of the site, Charles Lester (Electrolux137) who know far more than me and also some people who worked for Electrolux long ago and know much more than me. My knowledge comes from my observations over time and also these members who have helped educate me even further with their vast amount of knowledge.

Jon

Jon


Post# 431639 , Reply# 16   9/11/2020 at 15:25 (1,294 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
The factory rep that sold her the unit was a church friend. I hated going over there when I was little. Lol.
I remember it going in for service through the years. We had loner Electroluxe vac’s till it was fixed.
I found a guy on line, he said he can restore the cord winder. Terry, in ILL. Anyone here ever use him?
Yes, it looks like Dec 19, 1959. Mr York was his name.
On the bill shows a garment bag, filter, N spare tool, .87¢. Lol $109.21 for all.


Post# 431641 , Reply# 17   9/11/2020 at 15:48 (1,294 days old) by dysonman1 (the county)        

dysonman1's profile picture
That's so sad. In December of 1959 she could have had the power nozzle. It was available and would have made a world of difference.

  View Full Size
Post# 431644 , Reply# 18   9/11/2020 at 16:17 (1,294 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Where would you plug that in at?
Was the orig power cord tan?


Post# 431686 , Reply# 19   9/12/2020 at 15:24 (1,293 days old) by Jo (Dallas,TX)        
Yes

The original power cord was indeed a warm gray or tan.

The AF’s that were equipped with power nozzles had a small outlet added to the right side of the chrome trim along the top of the cleaner Close to the front.

It was a retrofit that the dealers could add I think if the customer opted for the power nozzle. Though some may have come from the factory with it...I was originally thinking the early F’s didn’t have it but this would be wrong as yours is a late F so this leads me to believe it was a retrofit. Likely the factory supplied dealers with a specially designed clipper to clip out the trim perfectly and this plug was designed to slip on the trim. This way they could do it right in the customers home in a few minutes and sell a lot of their model AE and AF customers from the last few years the new power nozzle without having to replace the entire machine. It wires directly back to the switch as I’ve disassembled mine just recently to paint it and mine has it. I have posted a picture of mine that shows it. There is a little rubber cover you have to lift to reveal the outlet, mine is starting to rip off unfortunately but I’m careful with it when I use it but I don’t need to use it much. Keep in mind that mine is repainted a hammered gold. Long story as to how it ended up repainted, but was indeed the same colors yours is when I got it and somewhat scratched and little tiny peppered rust spots on the upper half so it didn’t look great. For some dumb reason I decided to paint it dark bronze and that all chipped off horribly and it looked like crap so I did it again with better paint, several coats, And better prep and It looks much better. If I hadn’t had the gold hammered paint already I probably would have done my best to repaint it in spray paint as close to the original colors.

Electrolux used this little retrofit for many years and even included it on rebuilt G models that didn’t originally have the power outlet there. Most all models of the R, G, and L have the power Plug on the bottom by the right front wheel and a small portion of the early model G’s had them under the automatic control dial but that location tended to have problems with the cord pulling out so they moved it Just forward of the right front wheel Location where it had been on the model R which proved to not have that issue. This location was normal through 1979, When the last of the Model L’s was made using a “pigtail” electric hose or non electric hose with external wire wrap on the hose.

You can retrofit your machine to work with a power nozzle by adding the outlet but obtaining one would be a challenge. I once used a power nozzle sheath cord to add one to an old AF that did not have one...those cords are more readily available. I just drilled a hole in the metal trim to feed the cord through and back to the switch...the end of the cord with the plug did dangle off the trim though.

The power nozzle makes the machine up to date And highly effective and easy for carpet cleaning Removing stuck on fuzz, threads, pet hair and the like in one stroke and even fluffing the nap and the power nozzle glides over the carpet effortlessly. So easily some people felt like it wasn’t doing a good job, but it indeed does.. Back in the 60’s the Electrolux with the power nozzle was rated number 1 by consumer reports as the best cleaning vacuum cleaner.

My Mom had a model S with no power nozzle and when my parents replaced all the carpet in the house with light Creamy yellow Carpet In the 70’s, she had the Electrolux salesman out to get the power nozzle. Unfortunately the model S could not be retrofitted with the power nozzle and I think she just really wanted a whole new vacuum for the best suction and to keep the other for the garage and basement so she bought the model L with the power nozzle and electric hose in 1972 or 73. I still remember sitting on the stairs when the salesman sold her the Model L as I was only 4 or 5. She still has both machines today and the model L is still in great shape...the S runs but being a basement and garage vac for all these years it has gotten dented up. Likely from my Dad not being too careful with it.

Jon


  View Full Size
Post# 431706 , Reply# 20   9/12/2020 at 22:47 (1,293 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I see 2 diff cord types reels on the F’s. Mine doesn’t have the chrome band around. What’s the story on the diff?

Post# 431764 , Reply# 21   9/14/2020 at 08:09 (1,291 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I preserved the vac bag cover, not sure why, but it is from the 70’s.

  Photos...       <              >      Photo 1 of 2         View Full Size
Post# 431769 , Reply# 22   9/14/2020 at 09:39 (1,291 days old) by Jo (Dallas,TX)        
Cord reel

The smaller one with the chrome band is an older version. It is similar to the all chrome ones on earlier models in design. The one you have is the newer version.

That bag package may in fact be an original from when the vacuum was new! The ones from the 70s looked different. But if not, it’s definitely from the mid 60’s as Electrolux changed their logo name design in the mid to late 60’s to have that ocular rectangle around the name which was in all caps. This was in preparation to the introduction of the model 1205 with that overall shape to the cleaner body in 1968 but the Logo was introduced a few years earlier as I’ve seen Model G manuals with the new logo and the model G was the predecessor to the 1205. The new name logo I mention may be on your crevice tool, it looks more recent.

It’s certainly fun to have something retro To the machine and that bag package indeed is.

Jon


Post# 431770 , Reply# 23   9/14/2020 at 09:43 (1,291 days old) by dysonman1 (the county)        

dysonman1's profile picture
The 1959 models of Automatic F came factory-equipped with the power nozzle outlet along the top trim. The Power Nozzle was $49.75 extra. The Electrolux-built cord winders had a black cord with belden end. It wasn't until second year of the model G that Electrolux made their own plugs and did away with belden.

Post# 431771 , Reply# 24   9/14/2020 at 09:45 (1,291 days old) by Jo (Dallas,TX)        
Also

This newer version cordwinder you have was continued on the model R, and model L through 1979. It was colored in the light tan or cream. For the F, R, and early white L’s then a teal blue for the model L, in 1968 and then a metallic Gold for the last few years of the model L. I’ve never opened an older model as I’ve only had one for a short time and it worked fine on a model E, but I have had many of the newer ones. The internal design is identical to the integrated one on the model G and that may be why it was redesigned...to use the same parts.

Jon


Post# 431776 , Reply# 25   9/14/2020 at 11:16 (1,291 days old) by human (Pines of Carolina)        
Power Nozzles...

human's profile picture
I can attest to the difference a power nozzle and a good hose make. I have two Electrolux 1205s, one of which my dad rescued from a neighbor's trash pile in about 1981. It had a very leaky non-electric hose and no power nozzle. It was practically useless on the shag carpet we had in the house at the time. I got hold of my second 1205 at a thrift store in 2004 and it had a braided electric hose and PN1. Amazingly, the hose didn't leak terribly much, although the plastic pistol grip was cracked where it met the hose. The difference between the two machines was like night and day. I found the original 1205 in my parents' attic four years ago and carried it home with the idea of it serving as a parts donor for my other one, should the need ever arise but out of curiosity, I put a good vinyl hose and a power nozzle on it (probably the first time it had ever had one attached and also the first time the machine had been powered up at all in about 20 years) and gave it a test run. I was amazed that it performed every bit as well as the other one and now it is every bit the workhorse as any of my other Electrolux canisters.

Post# 431782 , Reply# 26   9/14/2020 at 13:50 (1,291 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I got the flip brush today from eBay, it’s almost nOS.
I sent the cord winder off today to get rebuilt.
Here’s the crevasse too. I’m guessing she had to but the dust brush then, something is on the receipt for under a dollar.

I guess good thing I saved the bag package, I sprayed it with water, then cut 2 PCs of pink foam for inside. Pressed it overnight. $3.45 for 18 bags, it’s gotta be old.


  Photos...       <              >      Photo 1 of 2         View Full Size
Post# 431783 , Reply# 27   9/14/2020 at 14:00 (1,291 days old) by Jo (Dallas,TX)        
Interesting dysonman1

What’s odd is his Mom’s receipt of purchase of this machine shows December 1959 but there is NO power nozzle outlet on the machine. So perhaps the factory Was sending some out with The outlet and some without the outlet...though it is possible I guess that it was from 1958 and sat in the dealer’s stock room for a while if more people were buying with the power nozzle until someone came along wanting one without the power nozzle.

Jon


Post# 431784 , Reply# 28   9/14/2020 at 14:05 (1,291 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
The brush I just got in the mail is a later version, it has the real rubber, but it was so new I just had to have. I did buy a tan rubber one, hope it’s older and has the correct slot on the one side. We shall see.

Post# 431786 , Reply# 29   9/14/2020 at 14:14 (1,291 days old) by Jo (Dallas,TX)        
Nice

That’s a beautiful teal and tan rug and floor tool, hard to find those in that combination of colors in that good of condition, usually they are well worn and the bumper corners are well rounded from wear like your original.

The dusting brush/upholstery tool is original and matching colors...nice...the crevice tool looks like it’s a 1974-1982 series cream colored and has the new Electrolux logo I mentioned started in the late 60’s but not with this coloring until 1974.

You are familiar with how the dusting brush works, right? The wings flip out and you can put the hose into the bristle end and I now it’s an upholstery tool and can even contour to rounded arms on wing chairs and couches and even bolster pillows! This and the flip over rug and floor tool are by far my most favorite tools of all vacuum cleaner brand tools. So convenient...4 tools in 2! The wings are replaceable if they ever break, but I try to be careful as I did break one one time back in the Late 80’s or early 90’s When I dropped the hose with it on and it hit the floor. An Electrolux man showed me how...you run the base under hot tap water to warm the rubber and then you can bend it to open it to release the wing hinge. He had spares from used ones and gave us a used one to replace the one broken wing!

Electrolux designed the entire machine to have replaceable parts and is completely serviceable...and while now Aerus has discontinued some of the parts, if you can get a part somehow, it can be replaced.

Jon


Post# 431796 , Reply# 30   9/14/2020 at 14:57 (1,291 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I was thinking we always had the crevasse tool, maybe the orig hose end was wore on an angle, when the hose was replaced she bought that then, I know I always got yelled at when not putting the tool on. Lol

Post# 431810 , Reply# 31   9/14/2020 at 20:10 (1,291 days old) by Jo (Dallas,TX)        

Doe the manual show a crevice tool included? I know my Mom’s model S made at the same time did not include one. It was an extra purchase item. Your Mom may have bought one but the early ones were hard breakable plastic,
Erhaps it broke and she got this new one. Anyway, good that you have one! The generic replacement hose you have seems even more recent than the crevice tool and would not have been purchased from Aerus Electrolux....maybe the second hose wore out and she got this one on line or at a general vacuum store. General vacuum stores do not stock new genuine parts, only used stuff as they do not have access to them.

Jon


Post# 431813 , Reply# 32   9/14/2020 at 21:06 (1,291 days old) by Real1shep (Walla Walla, WA)        
I don't......

want to get into a member Battle Royal(pun intended) but.......

In one room that is carpeted sat something heavy that smashed the pile down. I've hit that spot with my Royal, my Hoover Convertible and the PN for the Diamond Jubilee.

Guess which one is the only vac that completely raises the pile back to normal(after many tests weeks apart)?

Kevin


Post# 431831 , Reply# 33   9/15/2020 at 07:42 (1,290 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
That isnt a Electrolux hose? that’s strange, I remember when the OG hose wasn’t usable, could have went through 2 hoses, at some point Mr York passed away, (factory rep) that’s all possible then. At some point it was retired for an upright, we just used the F for the cars. Leaning her place out, I didn’t see an upright. Hmmmmm

Post# 431835 , Reply# 34   9/15/2020 at 08:07 (1,290 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I’m looking at the manual, it’s a 1957, it doesn’t show a crevasse tool

  View Full Size
Post# 431836 , Reply# 35   9/15/2020 at 08:09 (1,290 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
The cloth bag was in this. It isn’t Electrolux.

  View Full Size
Post# 431846 , Reply# 36   9/15/2020 at 11:09 (1,290 days old) by Jo (Dallas,TX)        

The cloth bag you have in earlier photos and your profile photo is indeed an Electrolux. I have the same one. I think it just got put into an empty package from some generic DVC brand paper bags. Funny, I keep my cloth bag in an empty plastic bag from some generic paper bags too!

Your cloth bag fits a number of models..Automatic E, F, G, 1205 and most models since that take the c bag. Interestingly enough there is also a clear plastic cover for the top of the bag with a hole in the center for the suction port to help contain the dirt. I’ve seen these but never had one. I think they may have been for use with the later models such as the Golden jubilee and on. It really helps the dirt from dirtying up the inside of the bag door.

The cloth bags were used by salesman to demonstrate the dirt the vacuum would pick up in a customers home.

I remember once when staying at my Grandmother’s house the Electrolux man coming and he dumped the cloth bag half full of dirt on her nice formal living room chair. She got very angry with him and told him to “clean up that mess” and not to come in her house and make a mess like that, He showed her how the power nozzle head put right on the end of the hose without the wand would clean the chair beautifully. Even so, she still was not very happy with him and sent him on his way with no sale as she already had two Electrolux’s. Of course I was right there watching the whole demonstration. My Brother and Sister were there too and my Brother remembers this instance to this day as well.

I think he was demonstrating the model 1205, the power nozzle was a blue PN-1 I do remember that for sure. My Grandmother got sucked in to the Electrolux salesman’s tactics and changed her Electrolux’s more frequently than needed. She always had one upstairs and another downstairs, usually the lower level model upstairs. She did like to have things new and have the best and kept a very clean house so getting a new vacuum periodically didn’t seem all that unusual to her. On this visit though, she did not buy the machine and sent him on his way. I think my Aunt who lived with my Grandmother allowed him to come in more for entertainment for us kids and especially me because she knew I liked to play with the Electrolux a lot. Our parents were away on a vacation or an out of state wedding I think and us kids were staying at Grandma's for the week so keeping us kids preoccupied was somewhat of a challenge.


Post# 431849 , Reply# 37   9/15/2020 at 12:23 (1,290 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Your rite, I meant the plastic bag wasn’t factory. Lol
Every time she took it in for repair, he tried to sell her a new vac. And the loaner was a newer unit.
I also have the sprayer and the vaporizer, still in boxes. I don’t remember her ever using them.
There are a few d3 to in the va, I’m wondering if my pointless dent guy could pop some of it out. I’ll ask him some time.
Looking forward for the winder to work. And having the bumpers on the front again, putting these on, do they just push in or do I need to take the front door apart?


Post# 431859 , Reply# 38   9/15/2020 at 15:27 (1,290 days old) by Real1shep (Walla Walla, WA)        
The Elux..........

salesmen were not always predators. I know of at least two that serviced their customers for over 30yrs......were never pushy and fixed their machines for pennies, if needed.

My mother-in-in-law was one of those customers. She lived in the same house for 45yrs and the Elux salesman was the same until he retired. She gave us an old G that she had(she had something newer).

Then she was instrumental in having the Elux salesperson come to our first farm over on the rainy side of WA. We bought a new Diamond Jubilee for a ridiculous amount of money.

Many yrs later we divorced;the ex got the Diamond J and I got the old G. Her cleaning lady absolutely destroyed the Diamond J. It was like watching an ape run a vacuum. I still have the G, but I transplanted its motor into a newer tank body. That was the strongest G motor I ever saw....must have been a story there but people pass on and provenance tales are lost.

Kevin


Post# 431861 , Reply# 39   9/15/2020 at 16:05 (1,290 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I got the other flip brush today in the mail, I would have never bought it, a day after 1 ordered it my orig one just fell apart, when I took it apart to clean, the screws broke off the plastic. This one is complete. If someone needs a teal one w/ tan rubber, it’s pretty nice. It has the elbow part too.

Post# 432083 , Reply# 40   9/19/2020 at 12:47 (1,286 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
My vac does not have the power port. I’m not going to add it, here’s with the parts I got so far, cord reel is out getting rebuilt and a rocker switch and a bumper is coming as well. It does work well as it is now.
Are the real Electrolux bags better than the repop?


  View Full Size
Post# 432088 , Reply# 41   9/19/2020 at 14:45 (1,286 days old) by Jo (Dallas,TX)        
I like...

Genuine Electrolux 4 ply bags...some were 3 or 2 ply and the new Aerus home solutions 2 ply bags in blue are supposed to be better Aerus says as the paper is supposed to be a better filtration media but some here have debated about that and I have some that I recently acquired at a thrift store last year but haven’t tried them yet. The “Multi filter” brand and “air plus” brand generics are 4 ply and are pretty good too but the top cardboard panel tends to be a little thinner sometimes causing them to warp inward if in the vacuum for a long period of time or run packing them heavily with dirt. The generics have come a long way and the 4 ply generics sold these days should do a fine job.

I bought 54 3 packs of generics years ago from the dollar store, thought it was a good buy at 33cents per bag basically....the plastic bag says they are 4 ply but some were not the multi filter brand 4 ply ones and turned out to have no printing on them at all and are 2 ply so I was not too happy about getting something different than what the packages says on the outside. They were sold by Home Care products and have the big “vac bags” labeling on the outside. I really should call Home Care products and make them send me replacements since they put something different in the package than what was advertised. There’s some wording about a satisfaction guarantee on the back of the package. But I think I have to send them the bags at my cost for replacement and kinda not worth it. It was odd, about half the packages have the nice 4 ply multi filter bags and about half have the cheaper thinner bags. I suddenly noticed when I went to open a new package and thought ..gee this package seems not as thick as the other and opened the thicker package as well to reveal different bags. Maybe this is why the lot was sold off to the dollar tree, perhaps Home Care Products discovered their vendor for the bags was not putting the right bags in all the packages. Even so, regardless of where I buy them, they should still honor the satisfaction guarantee. I chose to buy so many because I was running my remodeling business at the time and using the Electrolux a lot and going through lots of bags so I figured I’d stock up since they were less pricey at the dollar store. A three pack for a buck! Not bad I thought. I bought those over 10 years ago and have used about half of them...I think I bought too many!

On the 4 ply bags there is 3 inner layers of a soft tissue like fabric and this helps to filter the dirt and dust and avoid the pores of the outer paper from clogging too quickly and therefore allowing the bag to hold more dirt before it cuts off suction. I believe this was patented by Electrolux long ago and then when the patent ran out, the generic companies began copying the feature as this used to be a big point Electrolux made as to why their bags were “the best bag for your Electrolux cleaner.”

Trapping as much dirt as you can helps keep the motor from getting dirt in it as well as fine bits getting sent back out in the air.

Personally for the units I use in my house I use the Genuine Electrolux 4 ply bags...for the one I use for the “shop vac” type jobs to clean the car, garage and remodeling dirty jobs, I use the generics.

I’m not sure if the older genuine yellow bags From the 60s and 70s are 3, ply but I discovered some of the mid 80s bags in gray are only 3 ply and then they changed to 4 ply sometime in that color era. Probably the 3 ply patent ran out so they upped the quality to 4 ply and got a new patent to still have the edge over generic copied bags. The tan genuine Electrolux bags with Tan cardboard colored tops were all 4 ply. I have a bunch of genuine bags from most of these eras mentioned and I should probably cut one of each open to determine how many plies they are. I know some of the genuine packaging says how many plies they are in that package. A genuine package of the yellow “lightning bolt bags” doesn’t specify but does show a graphic of a difference and the graphic depicts 3 total plies.

Really old generic bags from the 50s and early 60s were just single ply or 2 ply and some didn’t have the rubber seal either, I definitely do not recommend using those at all.

Some have found fabric cloth type disposable bags with micro filtration by a generic manufacturer..I’ve never tried them and am sure they are not cheap.

Bags should never be emptied and reused..the paper takes a beating especially when trying to get the dirt out and then could split or rip when reusing it allowing dirt to get into the motor. I’ve had genuine bags split at the corner edge seams because they were older...fortunately the inner layers didn’t rip and held the dirt in but old paper bags can split just from age as the paper begins to break down just from sitting around for many years so I don’t recommend buying “vintage” genuine bags. I’ve had this issue with some of the older yellow genuine bags I picked up at an estate sale or bought off eBay. Those yellow bags are from 1982 on back. That’s almost 40 years or more!

Jon


Post# 432102 , Reply# 42   9/19/2020 at 23:15 (1,286 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Here’s what I bought, it says 4 ply, it was from a Vac store locally, I try to help local businesses since all what’s been going on, they actually said they would look at fixing the switch but I have a new rocker coming. I went there to get 1 alum tube wand , but only had the new steel ones that are chromed and no vintage parts at all. They have been helpful, I have a bag less Bissell upright, the power switch broke, they had a generic one that was red not black, but it works on the vac. It was an easy fix.

  View Full Size
Post# 432103 , Reply# 43   9/19/2020 at 23:21 (1,286 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Here’s the cord reel. I hope it all works like new when I get it back. I sent him the rubber stop part off the original.
The bumper on the door, is that just a push in or does the door have to come apart to install it?


  View Full Size
Post# 432105 , Reply# 44   9/19/2020 at 23:39 (1,286 days old) by human (Pines of Carolina)        
Multiflilter 4-Ply Bags...

human's profile picture
Those Multifilter brand 4-Ply bags are what I use in all my Electrolux machines, both canisters ('C' bags) and uprights ('U' bags). I buy them in bulk on eBay and can generally find 24 bags for about $15 with free shipping, which works out to a fraction over 62 cents a bag. I find they perform just as well as the genuine Electrolux/Aerus bags for a fraction of the price.

Post# 432127 , Reply# 45   9/20/2020 at 13:02 (1,285 days old) by Jo (Dallas,TX)        
About the best generic bag you can get

Aside from the micro filter cloth bags, those are about the best generic paper bags you can get so they should do fine.

That’s a model 2 cordwinder. It looks a bit beaten up like someone dropped the vac tilted up from the front on the pavement. When you get it back you might want to paint it With a matching paint so that scratched area won’t rust.

The cordwinder should have a plastic ring around the hole where the cord comes out. When I’ve had to open any of these, I usually flip the ring around as it wears down on the top side from the cord being dragged along it when pulling the cord out. It’s best though not to pull the cord out in an upward direction, but rather straight out so neither the plastic ring nor the cord itself suffer damage.

In the meantime an extension cord with a correct straight oriented female end will likely plug into the back end of the switch to give you a cord to run the machine sans cordwinder. This machine uses the same standard cord as the AE, R, and L so if you want one of them, you can search eBay for one and also get a cord halo and then you’ll have both the non cordwinder setup as well as the cordwinder equipped setup which you can swap out if you like. The cordwinder will add a significant amount of weight to the machine and I added one to my Mother’s L and then some years later she complained the machine was heavy so I converted back to no cordwinder and she was happy again. The cordwinder really wasn’t something she was concerned about having as much as a nice light weight heavy duty vacuum cleaner, which the Model L was touted as per the advertising on our box which she stored the unit in for many years until the box finally became kinda tattered and she decided it fit in the closet better without the box.

Jon


Post# 432128 , Reply# 46   9/20/2020 at 13:12 (1,285 days old) by Jo (Dallas,TX)        
Not sure on the bumper

I’m not sure on how the F bumpers install...you might look closely at if it wraps into the bag door inside at all, I know the ones on the model L do so changing them involves opening up the bag doors interior cover.

If it stops before the bag door edge perhaps it’s just a push in rubber item.

Post a closer pic of the bag door, both sides, the one missing the bumper and the one with the bumper...particularly showing if the bumper ends at the edge of the bag door or seems to wrap in and around the edge of the bag door.

I believe the bag door interior cover swings open if you take out the screws And slide the rubber gasket forward off the collar., I’d have to look at mine but it’s at a different property It was being used at now so I do t have it available to look at. Unfortunately mine was not equipped with the bumpers but one I had at one time was but since they were in tact I never had to deal with them and I actually wish this one I have now had them because they are nice if you accidentally pull the vacuum into a door frame, they soften the impact and avoid nicking your trim wood and paint.

I do wonder when they started putting the bumpers on the bag door. Mine has the power port for the power nozzle but not the bumpers. So odd.

Jon


Post# 432172 , Reply# 47   9/21/2020 at 00:32 (1,284 days old) by rivstg1 (colorado springs)        

rivstg1's profile picture
I appreciate this thread as I was planning on asking you all about quality C type bags. I wondered if any were made in cloth Hepa type/manner because those type keep the airflow so much longer than the paper bags even with filtrating layers inside the paper. Does anyone know of any?

Post# 432183 , Reply# 48   9/21/2020 at 06:47 (1,284 days old) by vacuumlad1650 (Wauponsee, IL)        

vacuumlad1650's profile picture
Vacuum America Clean brand makes a good HEPA C bag

Post# 432188 , Reply# 49   9/21/2020 at 09:06 (1,284 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Yesterday I got good and bad news from Terry,
He said there is 3 diff types of the cord reels for the F’s, mine happens to be the middle version, it has larger parts inside and it’s missing half of them, the Electrolux guy my mom knew must have robbed some when the cord was put on directly. So in his stash, he has a reel in teal, and the later F version, also a few early versions with the band around, I liked the 3rd version, only diff is it has 3 little bumpers to sit on when you stand it. ( see pics). Mine is next to the teal unit, I opted fir the same unit not the teal. If I do have to re paint it, has anyone found a matching paint or do I get some enamel mixed at a automotive paint shop and mix in a prevail spray bomb?
Also he’s sending the front bumpers, I’ll put 2 good ones on.
It’s crazy how many differences there are for F’s.


  Photos...       <              >      Photo 1 of 2         View Full Size
Post# 432190 , Reply# 50   9/21/2020 at 09:36 (1,284 days old) by luxlife (Under a Pecan Tree)        
Terry's contact info..........

Is Terry's email address still the same as listed on his website? I had to ask because I haven't seen a webtv email address in a long time.

Post# 432195 , Reply# 51   9/21/2020 at 10:51 (1,284 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Hers what I’m using, if it turns out diff, I’ll repost it

theelectroluxman@webtv.net


Post# 432196 , Reply# 52   9/21/2020 at 11:13 (1,284 days old) by luxlife (Under a Pecan Tree)        
Ok. I guess it works.

Thank you very much!

Post# 432198 , Reply# 53   9/21/2020 at 11:39 (1,284 days old) by Dysonman1 (the county)        

dysonman1's profile picture
The type two cord reel with the three little rubber feet is for the model R. It uses the same parts as the model G. The type two for the Automatic F used unique inner parts.

Post# 432203 , Reply# 54   9/21/2020 at 12:45 (1,284 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Well crap, it it what it is. I’ll hang onto the OG one, maybe one day I’ll find parts.

Post# 432204 , Reply# 55   9/21/2020 at 13:00 (1,284 days old) by Jo (Dallas,TX)        
Who knew?

I agree, so crazy the cord reels were changed but I guess F’s had the old cord reel first then the new one was introduced..then iit must have been quickly improved leaving us with the third version of parts which looks to have been identical with parts to the model L, R and G’s just different colors and I would say that’s the best one to go with because there were so many of those made so getting parts in the future would be less difficult.

I wonder if he can fit your new one with the flip open louvre? It’s a Nice touch and can be changed as I see the current one is broken off so just the tab remains. It directs the exhaust air upward so as not to blow any dust on the uncleaned portions of the floor around.

The first F I had...had the second version of the cordwinder I believe...it didn’t have the louver or the little plastic feet to stand on to avoid the metal from scraping the floor or the metal getting scuffed itself. My Brother ended up with that first F which actually belonged to a neighbor of ours. After his using it for several years the motor started smoking he said and so he threw it away several years ago. It may have had a black cord on it, that seems to sound familiar. It did not originally have the power nozzle power port.. But it did have the bumpers on the bag door. .I retrofitted the power nozzle port to it using a PN-1 teal sheath cord so it sounds like it was nearly identical to yours.

Funny thing is my Brother thought the cordwinder was the motor! He said the vacuum is so funny looking with the motor sticking out the back. I had to correct him and explain it was strictly the cordwinder and that was an option and that’s why it looked like that.

Electrolux was always working on improving the products so I’m not surprised things kept changing.

Glad to hear you have found bag door bumpers!

I noticed the model E’s and model F’s sound different. The F’s sound nearly identical to the L’s and the E’s, S’s, LX’s all sound the same. I did notice that these have different size fans which are thicker but not as large of diameter as the L type motors. Hence Electrolux clear did some sort of motor change starting with the F. I always like the tone of the L and was pleasantly surprised when I heard my best friends Mom had her F running that it sounded the same. So when picking a model to replace the E I was using as a shop vac I decided on an F for several reasons.. the unit’s carry handle is sturdier and doesn’t rip which is a problem on the E’s R’s, and L’s. it included the automatic control which I like, it has the power nozzle port for sometimes I need to use the power nozzle, It isn’t as heavy as a G, and the motor sound is pleasant in general. I did consider an1205 as well but with that one I’d have to use the electric hose for the power nozzle instead of the external wire wrap which I already had and finding an early 1205 with the power port below the hose inlet is more rare.

I’ve never had an AE to know if it uses the same motor as the E or F/L, but I’m assuming it uses the same as the E.

Jon


Post# 432205 , Reply# 56   9/21/2020 at 13:23 (1,284 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Thanks all for the info here BTW, he said has a vent for the back, but I was t going to get it, it’s in teal, now I’ll tell him to put it on. I did get a halo fir $25 for the heck of it. He was a pleasure to work with too, looking forward to getting the parts.

Post# 432206 , Reply# 57   9/21/2020 at 14:03 (1,284 days old) by Jo (Dallas,TX)        
Perhaps

You might eventually find the louvre for the back in the tan/cream color on eBay. They were made in that color during the R, Bronze G’s and early white L’s and the last Gold L’s. The trick will be figuring out how people name them on eBay to search for them and find them. The teal Louver won’t be bad though And will match your floor tool. They were also made in the turquoise color for the Turquoise model G’s. Just writing this makes me realize that they were in 3 colors over time and changed for so many different models, not just the two colors which I thought was the case.

Jon


Post# 432220 , Reply# 58   9/21/2020 at 16:35 (1,284 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I called him back, and he said it’s blue, not teal. So I’ll look for one. He’s got a blue if anyone needs one.

Post# 432622 , Reply# 59   9/27/2020 at 13:02 (1,278 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I got my parts from Terry yesterday, everything was nice. Even though the cord winder is off a later Vac, it matches. It came complete with the switch cord, I do have an extra from tan bumper if anyone needs one. I also got a cord halo not sure why, but I he had a few nice ones. My mom sure would be happy it’s all fixed up. It gets a retired life now just cleaning the finished floor in my garage. The sound just brings back memories, thanks to all who helped with questions here.
Terry is top shelf on parts and service. I’d recommend him for your Electrolux needs.
I need a tan vent for the winder. I’ll have to scour eBay.


  Photos...       <              >      Photo 1 of 2         View Full Size
Post# 432661 , Reply# 60   9/27/2020 at 21:26 (1,278 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I see after filers avail, we never had these, are they good for the vacs?
Does it go in last, by the door?


Post# 432668 , Reply# 61   9/28/2020 at 00:38 (1,277 days old) by electrolux137 (Los Angeles)        

electrolux137's profile picture

~
~

When the four-ply bags were introduced, Electrolux instructed users not to use filters in their LXs, LXIs, Es and E-As. Then when the F came out, filters were discontinued. There's not even a way to install them.


  Photos...       <              >      Photo 1 of 3         View Full Size
Post# 432686 , Reply# 62   9/28/2020 at 07:45 (1,277 days old) by kirbyklekter (Concord,Ca.)        
I think I read here

that Electrolux owners manuals were printed up in huge batches and they would use the left over stock on the the next model if they could. If the model had a long production run, and they used the same manual without reprinting and editing I could see how certain features and improvements made during said run weren't shown or mentioned.

Kirby did similar during the 500 series. I have four manuals for various models that either borrowed most if not all of the previous models copy. Same manual, different cover. I've learned that you can't always rely on the owners manuals to determine when a new part or feature or change to a given model came about.

Printing is expensive so I can see why they would try to get the most mileage from a print job. It's very common now days for instruction manuals to cover 5 or 6 models in consumer electronics for instance and appliances where the only changes made were cosmetic.


Post# 432687 , Reply# 63   9/28/2020 at 07:49 (1,277 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I’m going to paint the metal part of the extra floor floor brush I bought on eBay tan, and use the tan rubber from it. The teal just looks wrong on this vac. I have 2 paints, a tan and an almond. I’ll see what matches. I have a nice teal floorbrush plastic pc if someone needs one in the teal.

  View Full Size
Post# 432688 , Reply# 64   9/28/2020 at 07:54 (1,277 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
E137, thanks. I thought you maybe just set in in before the bag, I just bought 24 bags for $16 and change, free ship on Amazon.

Post# 432701 , Reply# 65   9/28/2020 at 11:18 (1,277 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I’m going to attempt to paint the metal part on the brush side, it’ll be kinda hard not getting paint on the bristles, looks like the brushes are crimped in. Here’s 3 tans I had, I did a spray out to see what matches best, it’s an extra part so if it turns out bad, no biggie. The paint on the 2nd druse I bought is almost perfect, so I’ll save that one. My mom put a teal brush on there, not sure why. Her Electrolux guy always gave her wrong stuff.

  View Full Size
Post# 432710 , Reply# 66   9/28/2020 at 12:56 (1,277 days old) by Jo (Dallas,TX)        
I think trust had been changed

I think by then Electrolux may have changed the color scheme to the teal and tan as that was next to coordinate with the new model G. I know a lot of Electrolux’s that were sold with different colored parts as original equipment.

For painting make sure you sand first. Next mask the bristle strips with tape or you and uncrimp with a screwdriver and remove them they are in their own crimp strip. The bristle strips are replaceable and you just receipt to close it back up to hold the strips back in place.

The correct color for the metal piece for an F would have been the main color of the tank which is that beige gray color....Not the creamy tan color of the ends of the machine.

Also several costs will hold up better.

Let us know how it goes and comes out!

Jon


Post# 432712 , Reply# 67   9/28/2020 at 14:36 (1,277 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I can barely see the color in Jo’s pic. But it looks gray.

  View Full Size
Post# 432713 , Reply# 68   9/28/2020 at 14:48 (1,277 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I stumbled on this on the web. This is the hose I’m looking for I take it?

  View Full Size
Post# 432721 , Reply# 69   9/28/2020 at 17:48 (1,277 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Jon, you gave me an idea, so I tried to slide out 5he brushes, a little here and there, and they popped rite out. I straightened up the grooves where they staked the brushes a5 the factory. Now I can wire wheel the steel pc and sand with the brushes out of the way. The brushes say fuller brush on the bottoms. Then I scrubbed everything, way better.
Here’s a gray that I had laying around, rustolium Stainless Steel. Should be fine, not exact but it’s on the brush.


  Photos...       <              >      Photo 1 of 3         View Full Size
Post# 432762 , Reply# 70   9/28/2020 at 21:42 (1,277 days old) by johnnyb59c (13240 n 3980 rd dewey oklahoma)        
daaaaaang...

johnnyb59c's profile picture
$100 in 1959 would be like $893.19 today

Post# 432769 , Reply# 71   9/28/2020 at 22:45 (1,277 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Funnier yet, I spent more than it initial price to refurb it 😂

Post# 432792 , Reply# 72   9/29/2020 at 14:11 (1,276 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Got her all cleaned up, I’m not happy with the paint, I need to go to Home Depot anyway. So I’ll look for a better gray.

  View Full Size
Post# 432797 , Reply# 73   9/29/2020 at 14:50 (1,276 days old) by Jo (Dallas,TX)        
Maybe...

Maybe it’s the metallic finish you don’t like perhaps. Though the ones in the late 80s and on were just steel with a clear coat on them so it looked a lot like this. Glad you were able to get the bristles out, definitely makes things easier.

Yes Fuller did make the brush bristles for Electrolux and other vacuum cleaner brands too. Not sure how long they did that for them. But Electrolux made so much of the entire machines themselves that perhaps this they decided to have outsourced. Today’s floor brush and combination rug and floor tool uses plastic bristles. I do NOT like them in comparison. The bristles bend over especially on the front edge. The dusting brushes are still real horsehair though. Some of the real horsehair ones were all black and others a mix of grays. You can actually buy new bristle strips for these. I did some years ago on ebay and they are real horsehair.

Jon


Post# 432804 , Reply# 74   9/29/2020 at 16:27 (1,276 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
The Krylon gray paint matches pretty good for the flip brush.

  View Full Size
Post# 432811 , Reply# 75   9/29/2020 at 19:46 (1,276 days old) by Jo (Dallas,TX)        
Looks pretty good!

I like it, looks pretty darn close from the picture!

It’s nice that your canister doesn’t have any rust. Mine had little speckles of rust all on the upper half of the canister and that made me want to paint it.

Jon


Post# 432812 , Reply# 76   9/29/2020 at 20:13 (1,276 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I finished up the floor brush, I swapped out the better brush strips too, thanks for the idea, it came out nice, prob looks like It did new. I think the teal brush replaced the OG tan one, I remember something breaking. Now I have a nice all teal brush if someone needs one. Even has a teal thumb lever pad.

  Photos...       <              >      Photo 1 of 4         View Full Size
Post# 432836 , Reply# 77   9/30/2020 at 01:03 (1,275 days old) by electrolux137 (Los Angeles)        

electrolux137's profile picture

~
~

Nice. What color Krylon is that? The closest match to Electrolux Gray was called Dove Gray. Unfortunately it's no longer made.


Post# 432841 , Reply# 78   9/30/2020 at 07:36 (1,275 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Krylon gloss vintage gray, if you were to do the whole vac it would prob be ok. No primer with this one too. It’s hard matching 60 year old paint, I’d have to take the vac apart and get at where it’s been cover from light. Terry owes me a switch, but the vac is perfect now, I’m happy.

Post# 432842 , Reply# 79   9/30/2020 at 07:38 (1,275 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Here, I should have posted it.

  View Full Size
Post# 432845 , Reply# 80   9/30/2020 at 10:08 (1,275 days old) by Jo (Dallas,TX)        
Came out nice!

That looks very nice. If you have another canister vacuum that uses the standard 1 1/4” wands you can use the extra rug and floor tool with it if you like this tool. This is one of my all time favorite tools because it works so nicely and is durable and scratch free for hard floors and also works on rugs too nicely all in one so I have kept extras to use on other vacs that I acquired without such tools or that had tools that were not nearly as nice as these are. Heck, you may come across an Electrolux in the future you get free and need one to go with it!

Did you notice that the gleaner bar is different on the two? Yours has the option to switch it on and off and the grooves are quite aggressive to pull up hair and fuzz and even lift nap while it was redesigned on the teal one to be a different type of smoother groove that would work for all types of carpets and not get stuck on loop carpet so they eliminated the switching capability. During the teal color run they also eventually eliminated the thumb switch groove altogether. On the more recent models which are currently made, they have changed the gleaner bar to be nothing but a smooth metal bar, nearly identical to yours when it is “off” but yet the raised printing in the suction groove that says “Gleaner bar” with an arrow pointing to it is still there. (This raised printing was added in the mid 80’s). I’m sort of disappointed Aerus/Electrolux has made it all smooth, the generation just before it seemed to do some good to get up per hair and some stuck in fuzz, but I guess they figure people will use the power attachments for this type of cleaning. Seems odd to me that they downgraded this tool twice over time. I can see if it was getting stuck on loop carpet they would need something that would do the job on loop carpet so redesigning seemed logical. But complete elimination down to the smooth bar as current seems like a total downgrade.

Only the top of the line Lux platinum includes the tool now anyway, I think it is optional on the lower models Lux legacy and Lux Classic. Those include just a single sided floor brush tool that came over from the lexan models from Canada Electrolux when the two merged in the mid 80s.

Jon


Post# 432851 , Reply# 81   9/30/2020 at 14:43 (1,275 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Yes, I thought it was strange on the teal One it’s blank on the end, but still has the cut out area.
My moms had it, but it was a combo of later stuff since it broke.
I still have to replace the plastic rocker switch, but it works, so I’ll do that later.


Post# 432856 , Reply# 82   9/30/2020 at 16:21 (1,275 days old) by Jo (Dallas,TX)        
If I see one....

If I see one of those rocker switch covers on eBay I’ll be sure to let you know. The main switch body on my model G is identical and it sometimes doesn’t work and causes the vac to flicker on then off or not come on at all. Might be why someone gave it away and left it at the free stuff shed at the town trash and recycle station. Problem is intermittent. The switch unit itself is pretty simple and I can’t see what could go wrong aside from the spring breaking and that’s not it for sure but I have yet to take it out and examine it closely. It may just need a thorough cleaning. Apparently the switching unit is no longer made by Aerus/Electrolux so getting one is not as easy but an aftermarket company make be making a replacement which could be available at a generic vacuum cleaner repair shop.

How did those dents get in the side of the main body? Is there a story to go along with it? I remember my Mom’s model L tumbling down the stairs at one time when cleaning the stairs and that put a dent in hers. Kinda frustrating and it was back in the 70s when that happened as it was the main vacuum for the 2 story 4 bedroom 2 living and dining area house and was used weekly like clockwork. She still has it but it resides as the upstairs vac which is only 2 bedrooms and a bathroom for their vacation home that is only used primarily 3 months out of the year during the summer months.

Anyway it’s rare to find thIs series of metal units with no dents or scratches since they were prone to tipping onto their side. The model G’s are more common to not be dented because the back end was thick aluminum and the sides had thick rubber bumpers that ran down the entire length of the machine. I actually glued some model G teal bumpers to my Mom’s unit so as to avoid more dents. I think I did that in the late 80’s and they are still on there.

Oh by the way, did you know you can store the crevice tool on the vac too? While it’s kind of odd the narrow end will fit into the dusting brush end and stick up at an angle...also I sometimes store it by threading the narrow end into the handle. These options keep it “on board” and handy while cleaning. I’ve tried storing attachments on the cord clip at the back of the switch but often they fall off there. The cord clip is convenient for when there’s no cordwinder, just the halo, to either keep the end of the cord in place after winding it up or if one only needs a shorter length of cord just what is needed can be unwound and clipped to the clip so the rest stays firmly on the halo. I do wish they had built in a specific clip for the crevice tool...that would have made this series even better. The brush clip can hold it if it hasn’t gotten bent upwards but often they do somewhat from people pulling upward with their brush than just sliding it forward to remove it. It can be bent back by unscrewing it and bending it downward some then putting it back on and it will hold the crevice tool more firmly. But at least the clip is there to hold the multi use combination dusting brush/upholstery tool.

Jon


Post# 432862 , Reply# 83   9/30/2020 at 17:23 (1,275 days old) by Jo (Dallas,TX)        
Hose

This model F has the original hose on eBay. Also a cordwinder with the swing open back louver! Seems they’ve put a cloth bag in and didn’t realize you have to remove the bags gasket to get the door to stay shut and have it taped. Bet it won’t sell and you could pick it up cheap as they have a best offer option! They mis named it. That’s the cordwinder model not the machine model.

CLICK HERE TO GO TO Jo's LINK on eBay


Post# 432865 , Reply# 84   9/30/2020 at 18:27 (1,275 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Dang, if I didn’t just buy the reminder I’d snag that. I jumped too fast, It has the mill finish tubes, I needed 1 of those. Funny, it doesn’t have the front 2 rubber bumpers. And the vent is teal.
The cord winder from terry is cleaner looking. I’d lov3 to have that hose though 😑


Post# 432866 , Reply# 85   9/30/2020 at 18:33 (1,275 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
The dents were prob from me loosing it down the stairs many times. Mom used to yell. Lol
Before both staircases were carpet they were hard on the vac. Plus she stood it up in the hall closet, it fell over constantly. I’m surprised it’s not more beat up. In the end, the dementia set in, a lot of things she tossed without me knowing. She had a green upright vac, one day it was just gone. She threw it out.


Post# 432872 , Reply# 86   9/30/2020 at 20:14 (1,275 days old) by Jo (Dallas,TX)        
Glad she didn’t toss the Electrolux

Likely because it was easy to push. As people get older they lose their muscle tone and find using the Electrolux or a canister quite easy compared to uprights. Especially without the power nozzle. It happened to my friend friend who passed at 94...in her later years she didn’t clean the house herself but in her 60s and 70s if she had to vacuum (I mostly did it) she didn’t like using the power nozzle because it was easier just to use the rug and floor tool. My Mom is now 83 and has arthritis in her right hand and wrist and she is starting to not use the power nozzle every time she vacuums. I got her a eureka quick up stick vac with power brush and it’s very light and she uses that a lot so she only has to go around with the Electrolux every two weeks. I told her it won’t deep clean like the Electrolux and she agreed and says she still does use the Electrolux because since we got her the new rubber hoses it’s much easier to handle too she said but she likes to use the Quick up frequently.

Sorry your Mom ended up with Dementia, my Grandmother ended up with that too. They called it senility back then but it was very unfortunate. I was young at the time, just 11 and she died just before I hit 14. There was one time when she did recognize my Mother when we arrived for a visit and it was very surprising as it had been quite a while since she knew who anyone was except my Aunt who lived with her. My only hope was that she was not lonely during those years and I think because the mind was going she was living in this world of when she was much, much younger as she would talk about her husband coming home soon who actually had died when my Mother was just 3. Fortunately, she lived in the house she and my Grandfather built at a young age until nearly the end of her life so going through the senility in her house that she lived in at that young age made living there not an issue. Her daughter, my Aunt, never married and always lived with her so that I’m sure made it easy for her but undoubtedly was difficult for my Aunt.

At the early onset of it I do remember my Grandmother using the Electrolux and she would flip the rug and floor tool over but incorrectly, not removing it but instead spinning it over and the suction was at the top when she was doing the hardwood but it was ok, she also would go over the hardwood with a dust mop. She didn’t have a lot to do so she cleaned a lot and had worked In her early years cleaning for people. In the later years of the dementia you could give her an entire basket of laundry and she would be delighted to sit and fold it, or give her a dust rag and she would go around and dust everything sometimes more than once if you didn’t take it away from her once the laundry was folded or everything was dusted. Cleaning her house was something that she could do at her own pace and kept her busy during the dementia years and my Aunt just kept the toxic cleaning stuff out of the house. Unfortunately she would cut the wires for the stereo speakers with scissors to “clean that up” and that was funny. She liked everything orderly and neat and didn’t keep a lot of things around.

Yup, I notice many F’s some with and some without the bumpers. I wish my current one had them but it does not.

Yeah this would have satisfied most all of your needs except for the bumpers and the rug and floor tool.

I have a turbotool rug washer in the gray and tan coloring, it has a teal tank cap and a teal string hook for the dispenser plunger. I’ll take a pic and post it later. I forget that it’s in the match F colors. I found it sitting on someone’s trash one day she I was walking home from school when I was in the 4th grade. It was a half day as I think it was just before a holiday and for some reason I decided to walk home the other more difficult route and trash had not been collected yet as it was midday. I thought it was quite interesting and had never seen one ever so of course, it came home with me. I’m not quite sure when I brought it from NJ to TX. I must have put it in a suitcase and checked it on the plane but I have no recollection of that whatsoever! The design is similar to the cordwinder on the top.

Jon


Post# 432882 , Reply# 87   9/30/2020 at 22:45 (1,275 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Looking at the metal pc in the floor brushes, the metal part looks always lighter shade that the plastic parts.
Terry said no matter what condition of an original hose, it won’t be any good to use, anyone still have luck with a orig hose?


Post# 432899 , Reply# 88   10/1/2020 at 11:37 (1,274 days old) by Jo (Dallas,TX)        
Usually no but...

On rare occasions they may be good but usually have some leakage near the handle and machine end as those get bent and flexed to the extreme the most. The braided hoses were discontinued in the late 90s I believe and I think there was a transition period where Electrolux was making both. With that in mind and considering this is 2020, any braided hose will be 20 or more years old. Usually they crapped out somewhere between 10 and 15 to 20 years of age.

Mine that was purchased in 83 or 84 and used only a handful of times on my XXX. it is crumbling on the inner layer despite it looking virtually new and that’s a bummer and frustrating because my Aunt paid a lot of money for it just before she passed away. Then the vac was stored carefully in a box making sure the ends were not creased over at all but the inner material has just dried out and bits get sucked into the bag if I use it which is rarely. I do have one from a 1953 Model E that is fabric wrapped, it is different on the inner layer and surprisingly leaks only slightly by the handle but the inner diameter is smaller so it seems to reduce the suction power more than that newer one or the flexible rubber or plastic ones.

So I would say expect some leakage from a braided hose for sure and the amount will vary...just depends on how much it has deteriorated and been used. I think storage environment may have affected this too. Too dry and the rubber dries out faster. Last Christmas I discovered the braided hose for my parents basement Electrolux was leaking pretty bad so I had to just wrap the whole thing with duct tape so the machine would be effective when used. I’ll likely bring them a plastic or rubber one to replace it if I can ever get to visit them again with this pandemic.

While the braided ones are retro and pretty, a rubber hose is a true upgrade for functional reliable performance because anytime you put the cleaner under strain, a leaking hose will not have the suction power to pull the deeper down dirt up. Kinda like leaving the suction control on the handle opened, when it’s under strain at the hose end it defaults to sucking through the suction control valve and this is what happens with a leaking hose.

I’ve experienced some that are so bad you can literally feel the air being pulled in through the braided outer layer when the hose end is covered and the tone of the motor doesn’t change much.


Post# 432932 , Reply# 89   10/1/2020 at 22:12 (1,274 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Today was a day for wrong vac parts, I had a rocker switch coming also for the F, it showed up in tan. Not gray. Did the F’s have tan also, or is this from a diff model?
It’s perfect though, I just may have to use it, my OG one has a pc broke off on one side


  View Full Size
Post# 432934 , Reply# 90   10/1/2020 at 22:17 (1,274 days old) by Jo (Dallas,TX)        
That is from a bronze G

The tan would be from a bronze G or a rebuilt AE, AF, or G. Where Electrolux chose the tan color scheme for those parts. All 3 of those models use that switch and rocker cover. It will work though for you.

Jon



Post# 432935 , Reply# 91   10/1/2020 at 22:18 (1,274 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Looking at the lineup in electro137’s post on speaking of F’s, one F, has the tan switch. Was this Orig or a replacement?

Post# 432951 , Reply# 92   10/2/2020 at 11:06 (1,273 days old) by Jo (Dallas,TX)        
Hmmm

I did notice that too. All the F’s I’ve seen have had the grey switch cover so not sure if this tan occurrence is just a replacement.

Jon


Post# 432960 , Reply# 93   10/2/2020 at 12:48 (1,273 days old) by dysonman1 (the county)        

dysonman1's profile picture
The hose in the eBay listing is not a genuine Electrolux hose. It's a replacement hose with an incorrect handle end.

Post# 432974 , Reply# 94   10/2/2020 at 14:59 (1,273 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I almost bought this one. It sold fast. I don’t think it was correct.

  View Full Size
Post# 432978 , Reply# 95   10/2/2020 at 20:38 (1,273 days old) by electrolux137 (Los Angeles)        

electrolux137's profile picture

~
~

That clearly is not the correct hose -- wrong striping and plastic pistol-grip handle.


Post# 433064 , Reply# 96   10/4/2020 at 17:59 (1,271 days old) by Jo (Dallas,TX)        
That one...

Is from the super J years. The super J hoses were white with the triple stripes just like this. Electrolux made non electric replacement hoses all along but in the current models coloring.

Jon


Post# 433091 , Reply# 97   10/5/2020 at 09:43 (1,270 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Well, one of these days I’ll come across a correct new hose fir it. Half the fun of a hobby is looking for parts.

Post# 433093 , Reply# 98   10/5/2020 at 09:55 (1,270 days old) by Jo (Dallas,TX)        
Yes don’t be hasty

Don’t be hasty and quick to buy if it’s not correct or in poor shape, one that you really want will come along...may take months or a year or so if checking eBay every day to finally find it. Don’t get discouraged either. I’ve had luck at finding just what I want in great shape for hoses with lots of persistence and patience and time. These items are rare but do come up considering how many were sold and still out there and get out on eBay instead of thrown out or sent off to a thrift store.

Jon


Post# 433108 , Reply# 99   10/5/2020 at 18:44 (1,270 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Yes, I agree, I went to fast on the other parts.

Post# 433205 , Reply# 100   10/7/2020 at 18:01 (1,268 days old) by Jo (Dallas,TX)        
This is for you Roger

Came across this and I believe it is just what you are looking for! Correct color.

You’ll need to save and reuse the retainer spring clip when you take the broken off tab from the old one off.

Jon


CLICK HERE TO GO TO Jo's LINK on eBay


Post# 433221 , Reply# 101   10/8/2020 at 07:32 (1,267 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
That is is. Thanks.

Post# 433315 , Reply# 102   10/10/2020 at 09:15 (1,265 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I’ll try to message the guy. Looks like the sale ended. It’s not perfect, looks like a pry mark on it. I jumped the gun on other parts, so I didn’t buy it.

Post# 433317 , Reply# 103   10/10/2020 at 09:59 (1,265 days old) by Jo (Dallas,TX)        
Not often to find these

It’s rare to find these so that’s why I sent you the link. Most people don’t take them off. If it’s gone and you can’t find another you might have to check with Bryan Satterwhite at rvavacuums.com who does restorations to see if he has one. I didn’t think the pry mark was too bad.

Jon


Post# 433318 , Reply# 104   10/10/2020 at 10:03 (1,265 days old) by Jo (Dallas,TX)        
It’s relisted

I looked at the old link it shows no longer available but then there are options and it shows it has been relisted and I hit view relisted item. If a seller sets an expiration in the suction they will have to relist it after it expires. Unless he relisted it for you if you’ve been in touch. Yeah it’s not perfect but not bad... maybe make him a lower offer since it’s a bit damaged.

Jon


CLICK HERE TO GO TO Jo's LINK on eBay


Post# 433320 , Reply# 105   10/10/2020 at 10:38 (1,265 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Well, I guess I should nab that.

Post# 433322 , Reply# 106   10/10/2020 at 10:46 (1,265 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
And my vac has the dents, lol. It’ll fit rite in.

When I use the vac, you can smell a motor smell, hard to explain, should I do anything to the motor, the repair guy prob did things over the years, but after opening up that Eureka Upright and seeing how filthy it was inside, not sure if I should open it up or leave it alone ?


Post# 433333 , Reply# 107   10/10/2020 at 12:31 (1,265 days old) by Jo (Dallas,TX)        
Do you have an air compressor?

If you do then opening it up and blowing out the dirt would perhaps help. It’s possible the motor brushes could be causing a lot of sparking giving you the motor smell. It could also just be the rubber baffle or the metal inside that’s emitting an odor. I noticed almost all model G’s have a funny odor so could be something like that.

Jon


Post# 433344 , Reply# 108   10/10/2020 at 16:10 (1,265 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
What’s the process in taking it apart to blow out the motor?

Post# 433374 , Reply# 109   10/10/2020 at 22:19 (1,265 days old) by Jo (Dallas,TX)        
You’ll have to...

Take off the top cover where the switch is, unplug the cord. You’ll see a small acre holding the back end on, remove this screw, there is also one on the bottom. Then the back of the machine will slide off. There is a rubber gasket and you’ll have to put that back on when reassembling. Clean everything good around and with the gasket. You’ll notice the gasket likely has acre holes through it that you’ll need to line up when reassembling. And that’s it...pretty easy! I do t think you have to take the switch off but if you do it’s not too diffiicult just take pictures of the proper place the wires are screwed on it before taking it apart. Also the switch has a rod hooked into it that goes forward to the bag door that shuts the switch off when the bag door is opened or pops open from the automatic control. You’ll need to take note of how that rod is threaded into the switch.

I just can’t remember if the switch covers that little screw or not. If it doesn’t you may not need to touch the switch at all.

Jon


Post# 433406 , Reply# 110   10/11/2020 at 21:07 (1,264 days old) by Jo (Dallas,TX)        
And here’s your F original hose

Just found this...a bit pricey though. Exactly the original F hose.

CLICK HERE TO GO TO Jo's LINK on eBay


Post# 433408 , Reply# 111   10/11/2020 at 22:07 (1,264 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
That’s nice. Only reason I’m not jumping on that is I bought all the rest of the parts I needed too fast I think. I guess I’m looking for a that brand new hose in the box still. Lol. That is tempting. A few glasses of wine I’d prob buy it.

Post# 433412 , Reply# 112   10/11/2020 at 23:13 (1,264 days old) by electrolux137 (Los Angeles)        

electrolux137's profile picture

~
~

That latest photo is not a genuine Model F hose. I posted photos of the correct hose. The colors are wrong and there's no suction relief vent on the hose handle.


Post# 433416 , Reply# 113   10/12/2020 at 08:25 (1,263 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Your rite is is diff. A lot of variables on these hoses so then what kind of hose is this then?

  Photos...       <              >      Photo 1 of 2         View Full Size
Post# 433417 , Reply# 114   10/12/2020 at 08:27 (1,263 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Your rite is is diff. A lot of variables on these hoses so then what kind of hose is this then?
Is the vent just missing?


  Photos...       <              >      Photo 1 of 2         View Full Size
Post# 433426 , Reply# 115   10/12/2020 at 15:27 (1,263 days old) by electrolux137 (Los Angeles)        

electrolux137's profile picture

~
~

It's a bojack hose from a vac shop.


Post# 433427 , Reply# 116   10/12/2020 at 16:31 (1,263 days old) by Jo (Dallas,TX)        
Wow

Even I was fooled and I usually can tell a fake from a genuine Electrolux product very quickly. The colors look almost perfect compared to yours Charles. I don’t see any difference. I do notice the air vent missing so the handle must have been reused from an earlier model before they added the suction control air vent. The machine end even looks like it is an original but may have been a genuine but “reused” one. I know the modern day generic machine ends have a more curved transition between the tier steps.

I never doubt Charles Lester! His Electrolux knowledge and expertise is more than anyone I’ve ever encountered except perhaps from someone who worked for the company and paid attention to much detail.

Jon


Post# 433431 , Reply# 117   10/12/2020 at 18:06 (1,263 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I made an offer on that vent that was posed here and I got it. Lol let’s see how this fits.
I’m sure it’s missing a part I’ll have to hunt down lmao


Post# 433435 , Reply# 118   10/12/2020 at 18:35 (1,263 days old) by Jo (Dallas,TX)        
Just noticed something

Take a look at this F for sale on eBay...it too has what could be the original hose but the handle does not have the suction control vent either. Is it actually possible that some of the hoses had the suction control vent and others did not? This would possibly make that other hose on eBay perhaps an original?

Electrolux made so many changes here and there mid run of machines even including incorrect color hoses and attachments that I’m thinking any of this is possible....

Any weigh in on this Charles?


CLICK HERE TO GO TO Jo's LINK on eBay


Post# 433440 , Reply# 119   10/12/2020 at 21:11 (1,263 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
What’s up with the front, it doesn’t shut.

Post# 433444 , Reply# 120   10/13/2020 at 00:28 (1,263 days old) by electrolux137 (Los Angeles)        

electrolux137's profile picture

~
~

The above Model F has a bojack hose. Again, the pattern colors are wrong. The suction relief valve was introduced with the Model E Automatic and all models thereafter had one, except the Model T.

 

As for the tape on the front cover, I hate to say it but the owners might have been using it without a bag which is why the cover wouldn't close.


Post# 433447 , Reply# 121   10/13/2020 at 08:12 (1,262 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I think your rite on the no bag, it’s filthy on the inside.

Post# 433448 , Reply# 122   10/13/2020 at 08:15 (1,262 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I’m so glad my mom took care of the vac, it’s real clean inside.
Looking at the above link, the vent is teal. Funny.


Post# 433455 , Reply# 123   10/13/2020 at 10:26 (1,262 days old) by Jo (Dallas,TX)        
Cloth bag

I think they’ve been using it with a cloth bag and sometimes these machine can be difficult to latch with the cloth bag in place because the cloth bag has a gasket as well as the bag compartment has it’s own gasket in the same area. I have a cloth bag for my F, it does shut and lock but just barely and I have to push it pretty hard to get it to latch. Plus when the automatic control feature activates with a cloth bag in the machine dirt ends up dumping on the floor when the door pops open making quite a mess so perhaps one or both of these issues is why they’ve been using the tape. Also sometime people don’t understand that to stop the door from popping open almost completely they need to turn the dial up to 6 and this user may have no understanding of how to adjust the dial or what it does and that it could stop the issue so perhaps they instead just decided to use tape to hold the door shut. They also may have been using it to suck up plaster dust or ash, both of which will clog that cloth bag almost immediately and causing the door to pop open even on 6 so they may have just gotten frustrated and taped it to keep it running.

It definitely is a mess that someone created.

It’s hard for me to tell what exactly isn’t right in the color pattern of the hose compared to the original...I think even Detroitdirtbag has difficulty seeing it. What are the exact detailed differences you see on the hose material itself Charles? This way we can learn the difference. Comparing the photos I don’t see any difference in color or pattern and not sure Detroitdirtbag does either as indicated in an earlier post.

Jon


Post# 433470 , Reply# 124   10/13/2020 at 15:52 (1,262 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Yes it’s hard to tell in some pics on eBay. I just don’t remember the beautiful hose, it was like all grayish.

Here’s a pic of the inside of moms. Not bad for 61 years, pays off getting good bags.


  View Full Size
Post# 433528 , Reply# 125   10/14/2020 at 15:22 (1,261 days old) by Jo (Dallas,TX)        
That’s nice

Very clean indeed. Bet the motor isn’t too dirty either then. Have you opened up the back end yet?

My Mom has always used genuine bags in her Electrolux’s and also not used the vac to pick up anything but just household dust...no plaster dust or ash that could go through the bag so her machines are all pristine in the bag compartments too.

Looks like no one picked up anything wet either. It amazes me how many Electrolux’s I see that have evidence of moisture having been sucked into the bag. I had my niece use my F to clean a rental condo that is going up for sale and she cleaned out the fridge and somehow managed to suck up water with the vac. The bag was all wet and split open. There wasn’t water in the fridge so not sure how she managed this plus that’s a lot of water to have wet the bag that much and there was a water stain even on the bag’s cardBoard front. She had broken a glass shelf in the fridge and sucked up the glass with the vac as it was all tempered so broke into tiny pieces and I had not left her with a broom and dustpan.

Jon


Post# 433559 , Reply# 126   10/14/2020 at 22:46 (1,261 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Nope, I have not had it open yet.
Your niece could have sucked up some ice cubes. My mom almost ruined the vac once when she used that cloth bag to save on bags. I remember the Electrolux guy yelling at her. He took it all apart and cleaned it. Luckily she went to him or it wouldn’t prob be around for me to fix up.
I’ll have to read how to open it up,again, I think someone posted that.
I remember her telling me he passed away. He prob had a,out of stuff laying around. York was his last name.


Post# 433561 , Reply# 127   10/14/2020 at 22:59 (1,261 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I just saw 3 hoses on eBay.

https://www.ebay.com/itm/Set-of-3-Vintag...


  Photos...       <              >      Photo 1 of 2         View Full Size
Post# 433609 , Reply# 128   10/16/2020 at 15:20 (1,259 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I got the vent, it’s nice, but I’m missing a clip or something to hold it on ?

  View Full Size
Post# 433611 , Reply# 129   10/16/2020 at 16:30 (1,259 days old) by Dysonman1 (the county)        

dysonman1's profile picture
This is the original hose to the model automatic F. It has been in my collection since the late 1960s. Along with the vacuum cleaner, all the attachments, the power nozzle, and the original box. Look very closely at the colors and the patterns. It should help you in identifying an original on eBay.

  View Full Size
Post# 433614 , Reply# 130   10/16/2020 at 17:00 (1,259 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Nice pic, Thanks.

Post# 433650 , Reply# 131   10/17/2020 at 10:06 (1,258 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
So what am I missing to hold the vent in, the seller didn’t include it?

Post# 433669 , Reply# 132   10/17/2020 at 19:54 (1,258 days old) by Jo (Dallas,TX)        
Looks like 4 hoses in the pics

These are 2 gray Silverado electric hoses. A blue 1205 electric hose, and a super J era white non-electric hose. Electrolux phased out the metal handles during the 70s and 80s. The last metal handle I saw was on a gray Silverado era electric hose...instead of the plastic handle end, it had the end just like on the blue 1205 hose. I believe Electrolux made these for 1205 owners who needed replacement hoses and wanted to stick with the metal handles, they are more rare than common because the plastic electric handle will work with either the sheath with

Post# 433670 , Reply# 133   10/17/2020 at 20:04 (1,258 days old) by Jo (Dallas,TX)        
Vent clip

So look on your cordwinder...hopefully the clip and broken tab from the old vent is still there. It was in one of the pics of the cordwinder you posted here. What you will need to do is use a straight blade screwdriver in the center of the slot where the hinge is. You will see a cut out in the center. Put the screwdriver on the upper part of the bump out of the clip and push downward, the is will contract the spring clip and allow it to come out from under the metal trim. You will need to use this spring clip to hold the new vent on so don’t damage it or lose it.

To install you’ll throw away only the old broken off vent hinge tab and put the new vent’s hinge bar in the groove of the clip, and fit the bottom edge of the clip into the bottom of the slot on the back of the cordwinder first, then using the screwdriver push down on the clip bump out to contract it so the top fits into the slot edges.

Let me know if you have questions...

Jon


Post# 433671 , Reply# 134   10/17/2020 at 20:11 (1,258 days old) by Jo (Dallas,TX)        

www.vacuumland.org/TD/JPE...

I copied and pasted this photo from your picture above, it shows the broken off vent tab and the clip. I did see a picture after this one that shows the cordwinder after Terry sent it to you without the clip and broken off vent hinge. I hope he didn’t take it off thinking he was doing good and not put the clip back in. If he did, perhaps you can ask him to mail you the clip Since It was originally with it and you need it. Since he is into restoring this stuff I doubt he would have thrown it away and can send it to you.


CLICK HERE TO GO TO Jo's LINK


Post# 433675 , Reply# 135   10/17/2020 at 21:16 (1,258 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
He took the old clip out, he kind of does what he wants. I asked for my old winder back and he said he threw it out. Also he sent a tan switch when I asked fir gray.
The vent I just bought , is is broken?


Post# 433724 , Reply# 136   10/18/2020 at 11:34 (1,257 days old) by Jo (Dallas,TX)        
No

The vent is not broken. I was looking at the picture of the cordwinder you posted that I am guessing was going to be the one he was going to send you. But clearly after he sent you that picture he took the clip out and the broken off old bent tab. I guess you can contact him and mention that the photo shows it and ask to buy the clip from him. Hopefully it would be cheap and he will respect your wish to have the part That was originally on the cordwinder photo he sent you initially to complete your restoration rather than taking off the part and keeping it. Without the clip you won’t be able to attach the vent.

I’d contact him for sure to see if you can get it letting him know you have obtained the correct vent louver but need the clip back that appeared to be on the winder before he sent it to you.

Jon


Post# 433763 , Reply# 137   10/18/2020 at 22:49 (1,257 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
He took it off. Everything is extra. And like I said, he does what he wants. I said send me a gray rocker, he sent a tan. I put a note in the box, he threw it out. I deal is car parts, it is t that hard.

Post# 433775 , Reply# 138   10/19/2020 at 08:04 (1,256 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
What does the part look like I’m looking for to hold the vent on ?

Post# 433778 , Reply# 139   10/19/2020 at 10:18 (1,256 days old) by Real1shep (Walla Walla, WA)        
I'd be wary.....

about that eBay seller with the hoses. Yeah, they look "beautiful" but some of them could leak like a sieve....especially the 1205 hose. And typically if I ask them about hose leakage, they either lie or act confused/insulted at the query.

I've been the recipient of both buying hoses;outright lying and plain ignorance.

Also to have those hoses shipped to me it shows $32 which I'd have to add to the cost. Plus, I have to pay tax on Internet sales now.

I've never had to fix one of those end louvers before. I looked at a couple of G's that I have. If that pic is correct of the louver, then the plastic pin goes inside of a metal barrel on the back. Now I don't know if that metal barrel pries back enough to slip the louver pin in or it comes off somehow. But the plastic louver pin in melted in place and not serviceable.

Kevin


Post# 433779 , Reply# 140   10/19/2020 at 10:22 (1,256 days old) by Real1shep (Walla Walla, WA)        
Might be.....

different on the F model too....but I kinda think they are the same or similar.


Kevin


Post# 433782 , Reply# 141   10/19/2020 at 11:02 (1,256 days old) by Jo (Dallas,TX)        
Here’s an ides

It is basically a rectangular flat piece of spring steel that has a hump across the middle of it longways, this hump forms the place where it goes over the hinging plastic rod of the vent itself. It is just about as wide as the slot in the back of the cordwinder. You can see the hump in it from that one pic I copied above.

Jon


Post# 433797 , Reply# 142   10/19/2020 at 15:38 (1,256 days old) by electrolux137 (Los Angeles)        

electrolux137's profile picture

~
~

Good Lord.

 


Post# 433880 , Reply# 143   10/20/2020 at 22:02 (1,255 days old) by Jo (Dallas,TX)        
Wow

Yikes. That’s unfortunate. I’ll look if I have one in my parts bin in my closet but uncertain if I have one. Needle in a haystack you know. If I don’t have one perhaps a local Aerus guy would have one off an old machine. I’ve had some good fortune with some dealers that just made my day when I mentioned I had a particular machine but was missing something or a part was broken and they gave me used parts no charge when I was buying something else.

Jon


Post# 433892 , Reply# 144   10/21/2020 at 09:37 (1,254 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
If someone has the clip, let me know,

Post# 434321 , Reply# 145   10/28/2020 at 10:13 (1,247 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I saw this F on eBay, where does the exhaust exit?

  View Full Size
Post# 434323 , Reply# 146   10/28/2020 at 10:37 (1,247 days old) by electrolux137 (Los Angeles)        

electrolux137's profile picture

~
~

This is a very early version. There is no exhaust. The pressure inside the machine just keeps building up and building up and building up until it literally explodes. This problem was quickly remedied but not before numerous injuries and fatalities resulted from the poor design.


Post# 434324 , Reply# 147   10/28/2020 at 11:19 (1,247 days old) by Jo (Dallas,TX)        
Hahaha!

I must laugh at you Charles! That’s a good one! I can see shards of metal going everywhere as the back of the machine finally explodes! We need some humor around here even if it includes sarcasm!

But seriously...the bracket that the cord reel uses was indeed designed with a hole in it before the reel itself...the air just blows agains the opposite side of the reel housing and is deflected all around it. Not as good of a design because it could blow floor dirt around. I’ve found though the older design cord reels like this work better though but I’ve only experienced a few of them and for their age they really worked like new and whip the cords back in quite quickly. Never taken one of these older ones apart though.

Jon


Post# 435479 , Reply# 148   11/26/2020 at 10:03 (1,218 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
Post# 435532 , Reply# 149   11/27/2020 at 09:29 (1,217 days old) by dysonman1 (the county)        

dysonman1's profile picture
Why would someone try to sell an electric Super J hose with no pistol grip?


Post# 435537 , Reply# 150   11/27/2020 at 11:07 (1,217 days old) by human (Pines of Carolina)        

human's profile picture
dysonman1 wrote:
Why would someone try to sell an electric Super J hose with no pistol grip?

I reply:
People will try to sell anything. Whether someone actually buys it is an entirely different story. Chances are it leaks like a sieve and the handle has been reused on another hose. I bought a vinyl hose with no grip on the cheap one time but I had a handle for it in my parts box and was able to come out with a good hose. Had the hose been a woven one like that one, I wouldn't have bothered.


Post# 435542 , Reply# 151   11/27/2020 at 11:48 (1,217 days old) by Jo (Dallas,TX)        
Someone may buy it

Perhaps someone may buy it and put their hose handle on it unknowingly that these woven hoses often wear out and leak. It may not leak too bad yet but it’s bound to happen. But at this age I’d be surprised if it doesn’t leak. I did think this was stupid to see this listed for sale though but the seller may have damaged the handle and bought a whole new hose or I replaced the entire vacuum and is selling any remaining non broken parts. Those of us “pros” here know that these old woven hoses are generally useless except for collectible purposes of looks and display only and not for actual functional use.

This hose is actually a Golden Jubilee hose making it even older... the super J ones were white with gold and blue stripes. Probably someone who mixed up the models. Golden Jubilee and Suoer J look nearly identical at a glance and are often mixed up. The Super J is longer and the top cover’s back end is slanted out on a 45 degree angle to make it fit the slightly longer body. Aside from that and the 50th anniversary sticker on the Golden Jubilee or Super J logo on the chrome past the blower door there is virtually no other obvious visible differences so they often get mixed up. The super J’s are painted inside the bag door, the Golden Jubilee’s are not. The super J was likely named Super J because it had the better motor making it a “super Golden Jubilee” I think was the concept behind naming it. The Golden Jubilee anniversary was now over at this point as well but the model was selling well in the Gold coloring so simplifying it to “Super J” made the most sense but gold decor was still in during that period.

I remember my Grandmother’s Golden Jubilee when it was spanking new. It was really quite “glamorous” in comparison to the past coloring of most Electrolux’s which were predominantly recurring shades of teal blue with some occasional variations to bronze, beige and creams. It also of course was now still quite advanced as it was the second generation of the new horizontal rectangular body, something that became very popular with the blue 1205 and this just made it better and the change in the top panel too made it look even better and more advanced. My Grandmother had a lot of Gold accents in her house including in the carpet then, so the Golden Jubilee just fit right in to her formal decor much better than her previous blue 1205. As the Gold styling outgrew its time, almond came in and most appliances were white or Almond with brown or wood grain trim and control panels...so I imagine this is why the Olympia was chosen to be brown and cream. Surprised it wasn’t red, white and blue for the Olympics! But that likely would not have sold nearly as well but I don’t doubt the idea of that was at least brought up by someone when developing the Olympia, but perhaps the coloring may have been already chosen well before it became the official vacuum cleaner of the 1980 Olympic Winter Games which were held in Lake Placid, NY.

Jon


Post# 435563 , Reply# 152   11/27/2020 at 18:34 (1,217 days old) by electrolux137 (Los Angeles)        

electrolux137's profile picture

~
~

Jon, actually you have the GJ and SJ hoses mixed up: The GJ had the white hose and the SJ had the gold one.


  View Full Size
Post# 435568 , Reply# 153   11/27/2020 at 22:08 (1,217 days old) by Jo (Dallas,TX)        
Gee thanks

For correcting me. I guess somewhere I saw a Super J with the white hose initially and thought that was the correct hose. I really can’t remember the original hose on my Grandmother’s Golden Jubilee as by the time I was old enough to be more observant of the hose patterns she had already replaced the original hose with an Olympia series hose when the Electrolux man sold her the Olympia to replace her pristine model L.

Jon


Post# 435575 , Reply# 154   11/28/2020 at 08:19 (1,216 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
I don’t think the Electrolux guy gave the correct hose when my mom bought the F, it did not have any colors on it, it was just a grayish woven one. I’ll have to look through the home movies maybe the vac is laying around.

Post# 435578 , Reply# 155   11/28/2020 at 11:13 (1,216 days old) by Jo (Dallas,TX)        
Color matching and mismatching patterns and theories.

As I’ve mentioned before, I think some were equipped from the factory with non matching hoses and tools especially at end of a color or model change run. It would seem logical to be the case because it would be too much waste to throw away or sort and ship off the mismatched ones. Machines were sent off in complete boxes to the branches...but attachments and hoses were not just sent in the boxes with the machines but also to the branches as replacement parts when branches ordered them. The machine and parts usually were not paired together separately when someone bought a whole machine, usually the salesman would just give them a complete boxed set. But who knows what was really done at the factory for sure and afterward at the branches. Some Boxed sets could have been and I’m sure were broken down here and there if someone wanted to buy just a replacement canister unit and perhaps the hose but use all their old attachments from a previous model so then all the extra parts would have been added to the branch’s parts supply from the box set. Salesman likely weren’t attentive to color matching as long as it was a complete set or met the customer’s desired set they wanted. But from the amount of mismatching I noticed among people who bought new machines and received them with something mismatched, I’m led to believe mismatching was happening at the factory and it’s likely they didn’t have runs of different colors at the same time...just decided to change to the new color at a certain time and an older colored canister may have then been paired with a newer colored attachment or hose as the supply from each area was pulled from the bins along the assembly line pack up the box. Thinking about how a factory works that produces each and every item using molds and liquid plastics, coloring agents, paint supplies, dyes and so much more it would seem that when a color change was implemented it was done when the old colorant was used up and the new color supply had already been ordered for the new model’s colors so that’s what determined when the new models colors started production for all the attachments. There was likely a drop dead date for color changes to the canisters themselves to coordinate with the model changes and marketing as I don’t see canisters miscolored for the model number or letter. Since attachments and hoses were also sent off to the branches in indefinite quantities determined only by order demand from the branches beyond being included in boxed sets, the quantities of these produced were much higher than the canisters themselves which could easily create overruns or even shortages which would then create the mismatching situation right from the factory. I don’t think Electrolux was dedicated as much to color matching each and every unit that went out as that would not be a practical priority...as long as it had everything that was to be included, it would do the job and be a complete set regardless of color matching. Likely people didn’t question the coloring and just assumed “that’s the way it was made by the company” when they bought a machine because they didn’t have bunches to compare with and say, “hey that one has a matching hose, I want that!”

I’ve just seen so many mismatches where they came purchased this way that this is where my theory on this comes from. Heck, my Aerus Lux Legacy in light blue is all color correct except for the elbow for the combination rug and floor tool, that is next generation white. The entire tool was almost never used so doubt there was ever a replacement done, they may have run out of the dye for the light blue and already had the white dye ready to go if this was produced near the end of the light blue color run so the next batch of elbow connectors ended up white while everything else was still light blue. And this tool was not standard on this model anyway and likely thrown in to the sale or perhaps purchased slightly after...keep in mind the combination rug floor tool itself is color correct, just the elbow which comes off to is different. I didn’t buy the machine new, but likely I’m second owner. But for the most part, I do feel that most boxed sets had the correct color matched parts and the occurrence of mismatches was less than the amount of matches overall.

Only someone who worked in the Electrolux factory and perhaps oversaw how all of the production was occurring would know exactly what the practice and policy was for packaging and color matching.

I’ve also observed that if a color mismatch occurred, it was likely paired the following way...the older model canister had any combination of a next generation’s colored attachments. Not the other way around, usually won’t see a new generation canister with the older generation’s colored hose or tools. So likely they started the color change on the hoses and the attachments prior to the drop dead date of production of the next model so when the drop dead date arrived for the next model, all the hoses and attachments had already started production in the proper color so matching would occur on the newest model right away. Color matching wouldn’t be as high a priority on an outgoing model. But rather was selected to be the priority on the latest and greatest.

My best friends Mom’s model F has a model G hose. The lady I cleaned for had a blue L and it had a golden jubilee or super J gold colored hose and PN-2 with the golden jubilee sticker and I’ve seen many others with color transitions. I’ve seen blue hoses with cream handles instead of the blue ones and so on. But again, it more often seems to be the next generation’s colored attachments paired with the previous generation canister when there’s a mismatch.

That’s why I think your cream rug and floor tool with the teal bumper may have been the original included with the machine. The ones that were cream and teal were produced for the G. If the change happened before the G was produced, then them some F’s during the last year likely would have received some of the G colored attachments, hoses, etc, in any combination...just like my friend’s Mom’s F has the G hose but everything else is F coloring.

Lots of observation and thinking.

Jon


Post# 435694 , Reply# 156   11/30/2020 at 21:17 (1,214 days old) by kirbyklekter (Concord,Ca.)        
Guilty!

Years ago I cut the cardboard from the front of a used Electrolux bag to use in place of a regular paper bag. I did this when I was using the machine as a leaf blower on my front porch and also to fill a large air mattress. I get more air flow from the exhaust with less restriction. I put a colored piece of tape near the hose inlet to remind me to put a regular bag back when done. So if you ever come across an Electrolux with just the cardboard mounted in bag compartment,that might be one explanation!

Post# 435807 , Reply# 157   12/3/2020 at 12:47 (1,211 days old) by Jo (Dallas,TX)        
That’s scary

To know you could inadvertently run the vac with no bag in it. When I need mine to work well as a blower I just put a fresh bag in and don’t suck anything up with it and swap back the partially filled one when I’m done. The fresh bag blocks very little suction.

Jon


Post# 435824 , Reply# 158   12/3/2020 at 18:08 (1,211 days old) by detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
The only time I used it as a blower is when the hose would get clogged.

Post# 465206 , Reply# 159   8/9/2023 at 19:34 (232 days old) by Detroitdirtbag (Bottom of the Bag)        

detroitdirtbag's profile picture
It’s been a while, anyone have a correct hose for my F?

Post# 465214 , Reply# 160   8/10/2023 at 09:31 (231 days old) by dysonman1 (the county)        

dysonman1's profile picture
I have a spare Automatic F hose. I'll sell it but I'm not dealing with the hell of shipping.


Forum Index:       Other Forums:                      



Comes to the Rescue!

Woops, Time to Check the Bag!!!
Either you need to change your vacuum bag or you forgot to LOG-IN?

Discuss-O-MAT Log-In



New Members
Click Here To Sign Up.



                     


automaticwasher.org home
Discuss-o-Mat Forums
Vintage Brochures, Service and Owners Manuals
Fun Vintage Washer Ephemera
See It Wash!
Video Downloads
Audio Downloads
Picture of the Day
Patent of the Day
Photos of our Collections
The Old Aberdeen Farm
Vintage Service Manuals
Vintage washer/dryer/dishwasher to sell?
Technical/service questions?
Looking for Parts?
Website related questions?
Digital Millennium Copyright Act Policy
Our Privacy Policy