Hoover Turbopower U2334 Rebuild


Forum Topics & Rules Manuals & Literature	New users Click-here to sign-up

Thread Number: 24019
Hoover Turbopower U2334 Rebuild

[Down to Last]

Post# 268860 2/21/2014 at 18:36 (3,713 days old) by beko1987 (Stokenchurch, United Kingdom)
Checkrate/Likes November 1986 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 I'm sure it will look familiar to someone on here! Looks to be an early model too at 480! From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 All bar one screw came out of the handle cover, it was so rusty I tried for half an hour to tease it out using avariety of methods. Sadly none of those worked so I carefully snapped the housing around the screw. This should glue together and be pretty invisible, and I have another screw From Hoover Turbopower U2334 From Hoover Turbopower U2334 It came out with some pliers after this From Hoover Turbopower U2334 Handle Orf From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 Its been so long since I've done a hard bag TP I forgot it did this From Hoover Turbopower U2334 Thought how the hell is that going to come out of there etc From Hoover Turbopower U2334 From Hoover Turbopower U2334 Emptied From Hoover Turbopower U2334 Gulp, Autoflex next From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 Sorry, refrence shot! From Hoover Turbopower U2334 From Hoover Turbopower U2334 Had to chop this connector off From Hoover Turbopower U2334 And finally the beast was free! From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 Time for the botom end From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 Yummy From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 Pop the Bonnet From Hoover Turbopower U2334 From Hoover Turbopower U2334 Removed the 2 clamps and finally stopped it tipping backwards and wiping stuff off my shelf From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 From Hoover Turbopower U2334 I've never seen a motor setup like this. The screws were flathead rather than philips too I noticed From Hoover Turbopower U2334 Marked the location of the wires From Hoover Turbopower U2334 Blue is on the opposite corner... From Hoover Turbopower U2334 From Hoover Turbopower U2334 The fan was in fine fettle From Hoover Turbopower U2334 De fluffed the other fan, and soaked the bearing in plusgas which has it spinning much better now! From Hoover Turbopower U2334 Carbons about halfway through life, so plenty left for the future! From Hoover Turbopower U2334 Autoflex again now, and I consulted the 1990 book of Hoover From Hoover Turbopower U2334 From Hoover Turbopower U2334 All the tension went from the cassette, but thats fine because I can re-tension it when re-assembling (much easier when its back in the cover) From Hoover Turbopower U2334 I gingerly undid the spring cover, sprayed plusgas around and put it back... From Hoover Turbopower U2334 And gave the whole thing a clean up From Hoover Turbopower U2334 From Hoover Turbopower U2334 Picked the activator clean too From Hoover Turbopower U2334 It's soft as anything though so will wash it and try it, but I have a few better ones that will probably go on eventually. The green end ones can barely hold themselved up Had to clamp the bearings in the vice and turn the shaft with grips to get a bearing off From Hoover Turbopower U2334 And thats it for now. My U1222 is drying, so I'll wash this one Sunday hopefully!

Post# 270286 , Reply# 1 3/4/2014 at 22:58 (3,702 days old) by baglessball ()
Checkrate/Likes *DUDE!!!* I love to see your rebuilds, keep them coming!!

Forum Index:

Other Forums:

Comes to the Rescue!

Woops, Time to Check the Bag!!!
Either you need to change your vacuum bag or you forgot to LOG-IN?
Discuss-O-MAT Log-In

New Members Click Here To Sign Up.

automaticwasher.org home
Discuss-o-Mat Forums
Vintage Brochures, Service and Owners Manuals
Fun Vintage Washer Ephemera
See It Wash!
Video Downloads
Audio Downloads
Picture of the Day
Patent of the Day
Photos of our Collections
The Old Aberdeen Farm
Vintage Service Manuals Vintage washer/dryer/dishwasher to sell?
Technical/service questions?
Looking for Parts?
Website related questions?
Digital Millennium Copyright Act Policy
Our Privacy Policy