Thread Number: 26119
Kirby Brush Roll Question |
[Down to Last] |
Post# 292807   8/10/2014 at 23:26 (3,543 days old) by KirbyClassicIII (Milwaukie, Oregon)   |   | |
Checkrate/Likes
 
     
I'm wondering if among the four changes Kirby made to the brush roll for the Heritage II Legend was a replaceable sleeve bearing?
The reason I'm hoping to know is because in the promo slick for the Heritage II Legend, it says the changes for it included an improved brush roll, described as having "four engineering changes to increase brush roll life at least 50 percent." ~Ben
View Full Size
|
Post# 292826 , Reply# 1   8/11/2014 at 01:26 (3,543 days old) by super-sweeper (KSSRC Refurbishment Center)   |   | |
Checkrate/Likes
 
     
|
Post# 292991 , Reply# 2   8/11/2014 at 16:01 (3,542 days old) by KirbyClassicIII (Milwaukie, Oregon)   |   | |
Checkrate/Likes
 
     
|
Post# 293000 , Reply# 3   8/11/2014 at 16:30 (3,542 days old) by super-sweeper (KSSRC Refurbishment Center)   |   | |
Checkrate/Likes
 
     
|
Post# 293110 , Reply# 4   8/11/2014 at 23:20 (3,542 days old) by KirbyClassicIII (Milwaukie, Oregon)   |   | |
Checkrate/Likes
 
     
Alex,
From what I can gather, prior to Scott & Fetzer's acquisition of CWP in 1970 (during the same year the Kirby Classic first went on sale), the Kirby brush rolls had these available repair parts: AVAILABLE INDIVIDUAL PARTS FOR BRUSH ROLL 1482S (MODELS 2C/512) 1461S - Brush adjusting screw, large 1463S - Brush adjusting screw, small 1482 - Floor brush shell only 1500 - Brush shaft 1501 - Brush shaft groove pin 1520 - Brush yoke, small 1520S - Brush end complete, small 1521 - Brush yoke, large 1521S - Brush end complete, large 1522 - Brush bearing 1523 - Brush bearing cup 1524 - Brush bearing felt washer AVAILABLE INDIVIDUAL PARTS FOR BRUSH ROLL 1551S (513/D80) 1533 - Brush bearing corrugated strip 1534 - Brush bearing wave washer 1539 - Brush end plastic cap, small 1540 - Brush end plastic cap, large 1541 - Brush adjusting screw, 1-3/8" (models 514/D80) 1543 - Brush adjusting screw, 1" (model 513) 1551 - Floor brush shell only, 13" AVAILABLE INDIVIDUAL PARTS FOR BRUSH ROLL 155169S (1CR) 154169 - Brush adjusting screw 155169 - Floor brush shell only, 16" (remaining parts same as those for brush roll 1551S) In the years after 1970, there had been changes. I do know that no individual repair parts, with the exception of the brush adjusting screw (154169), were listed for the brush roll (152581) in the 1984 Kirby Heritage II service manual (773684). Later individual repair parts for the sleeve-bearing rolls were: 153471 - Brush bearing retainer 153571 - Brush bearing, bronze 1539 - Brush end plastic cap, small 1540 - Brush end plastic cap, large 154169 - Brush adjusting screw 155281 - Brush end plastic thread guard (2 used) ~Ben |
Post# 293146 , Reply# 5   8/12/2014 at 09:42 (3,541 days old) by super-sweeper (KSSRC Refurbishment Center)   |   | |
Checkrate/Likes
 
     
|